Emtek 96214 Heavy Duty Hinges (Pair), 4" x 4" with Square Corners

The Emtek 96214 is rated for doors up to 1-3/4 inches thick, which covers standard 1-3/4 inch entry doors as well as thinner 1-3/8 inch interior doors. It's a full mortise hinge, so the door edge and jamb both need to be mortised for a 4 x 4 inch leaf. Note it's a plain bearing hinge built for residential use, so on a heavy solid-core or high-traffic opening a ball bearing hinge holds up better.

Two hinges per order. The 96214 is sold in pairs and the mounting screws are included. Most residential doors take three hinges, so a single 1-3/4 inch door usually needs a pair plus one more hinge to complete the opening. Order quantity accordingly if you're hanging a full door rather than replacing a worn hinge.

The 96214 has square corners, which means it drops into a mortise cut with a chisel or a square-corner router template. If the existing pockets in your door and jamb have rounded corners, that's a 5/8 or 1/4 inch radius prep and a square hinge will leave gaps at the corners unless you square them out. For a rounded pocket, a radius-corner hinge such as the Delaney 4 x 4 inch residential hinge with a 5/8 inch radius or the Orca 4 x 4 x 1/4 inch radius corner hinge matches the existing cut.

Plain bearing hinges like the Emtek 96214 carry the leaf directly on the knuckle, which is fine for typical residential interior and entry doors. Once you're hanging a heavy solid-core slab, a door with a closer on it, or an opening cycled hard all day, a bearing hinge is the right call: the Orca 4-1/2 x 4-1/2 inch square corner ball bearing hinge or a Don-Jo HWBB74545 heavy weight full mortise ball bearing hinge covers that duty. For commercial openings, the Emtek is catalogued for residential service.

Not without recutting. The 96214 is a 4 x 4 inch hinge, so a 3-1/2 inch mortise is half an inch short in both the door edge and the jamb, and the screw pattern won't line up either. Either enlarge both mortises or stay at 3-1/2 inch. Emtek's Heavy Duty Hinges are also made in 3-1/2 x 3-1/2 inch, and for a square-corner 3-1/2 inch swap the Deltana DSB35 or the Schlage Residential S3P1010 are direct-size matches.

The Emtek 96214 is a 4" x 4" square corner plain bearing hinge in brass, catalogued for residential use and sold in pairs with screws. For a commercial opening in the same 4" x 4" square corner plain bearing configuration, the Orca Hardware 4" x 4" Square Corner Plain Bearing Commercial Hinge (4040 Series) is the direct counterpart, rated medium duty. It keeps the square corner so the same mortise routing in the door and jamb carries over.

The Emtek 96214 has square corners, so it needs a square cut mortise or a chisel to square off a radius pocket. If the door is already routed with a radius, the Orca Hardware 4" x 4" x 1/4" Radius Corner Plain Bearing Commercial Hinge (4014 Series) matches the 4 inch size and plain bearing action with a 1/4" radius corner, and the Delaney 4" x 4" Bulk Residential Hinges Exterior come with a 5/8" radius in pairs. Measure the existing corner radius before choosing between the 1/4" and 5/8" cut.

The Emtek 96214 is a plain bearing hinge, which suits normal residential door weight and cycle counts. Where the leaf is heavy or the door sees constant traffic, a bearing hinge carries the load differently: the Delaney 4" x 4" Commercial Ball Bearing Hinge Square Corner holds the same 4 inch square corner footprint with ball bearings, and the Orca Hardware 4-1/2" x 4-1/2" Square Corner Ball Bearing Commercial Hinge steps up to a 4-1/2" leaf, which requires a wider mortise than the 96214 uses.

The Emtek 96214 is a standard plain bearing brass hinge sold in pairs with screws, with no security pin feature. Where an out-swinging exterior door puts the pin on the outside, the Deltana DE44R5TA 4" x 4" x 5/8" Radius security hinge in steel is a pair built for that condition, and the Deltana CSB45N 4-1/2" x 4-1/2" Square Hinges use a non-removable pin. Note the CSB45N is a 4-1/2" leaf, so it needs a deeper and taller mortise than the 4" x 4" 96214.

The Emtek 96214 is a 4" x 4" hinge, which will not fill a 4-1/2" factory prep in a hollow metal frame. For that prep, the Don-Jo HWBB74545 Heavy Weight Full Mortise Ball Bearing Hinge 4-1/2" x 4-1/2" and the Hager BB1168 Non-Removable Pin Full Mortise Ball Bearing Heavy Duty Hinge are both heavy duty full mortise options, with the BB1168 adding the non-removable pin for out-swinging doors. For a wider door leaf that needs clearance past the trim, the Don-Jo HWBB75045 runs 5" x 4-1/2".

Solid brass, both the material and the substrate. That matters on exterior and coastal openings where a plated steel hinge can rust through at the knuckle, and it's why the unlacquered brass version will patina over time rather than flake. Leaf thickness runs 0.130 to 0.132 inch.

Ten finishes: Polished Brass Lifetime (US3), Unlacquered Brass (US3NL), Polished Nickel (US14), Pewter (US15A), Flat Black (US19), French Antique (US7), 606 Satin Brass, 613 Satin Bronze Oil-Rubbed, 619 Satin Nickel, and 625 Bright Chrome. That range is built to match Emtek knob and lever finishes, so a property manager standardizing a house or a floor of units can carry the same finish code across hinges and trim.

No. The 96214 is a plain mechanical brass hinge with no electrical provision. To get power or a monitoring signal from the frame into the door, you need an electrified hinge: Command Access ETH-BB68 is a heavy duty 5-knuckle energy transfer hinge, the ETM-BB68 adds an integrated door position switch, and BEST's CECB179-12C is a full mortise concealed bearing electrified hinge with a 12-wire quick connect.

Both hang a 4 x 4 inch square-corner mortise, but they're built for different service. The Emtek 96214 is solid brass, plain bearing, and specified residential, sold in decorative finishes to match door trim. The Orca 4 x 4 inch square corner plain bearing hinge is a medium duty commercial hinge, and the Delaney CH401X is a 4 x 4 inch commercial ball bearing square corner hinge. For an apartment unit door or a house, the Emtek is the finish match; for a corridor or a leased office opening, the commercial hinges are the duty match.

The Emtek 96214 covers 3-1/2" x 3-1/2" and 4" x 4" sizes in square corner, plain bearing brass. If the opening takes the smaller leaf, comparable 3-1/2" square corner options include the Deltana DSB35 3-1/2" x 3-1/2" Square Hinge, sold as a residential pair, and the Schlage Residential S3P1010 3.5" x 3.5" Square Corner Plain Bearing Mortise Hinges, which come as a pack of three rather than a pair. A three pack suits a door hung on three hinges without ordering a second pair.

Both are square corner plain bearing full mortise hinges, so the mortise prep is the same family of cut. The differences are material and count: the Emtek 96214 is brass and sold in pairs with screws, while the Ives 1010RP is steel and comes as a set of three, rated medium duty. On a decorative opening where the hinge is visible and the rest of the trim is brass in a finish such as Polished Brass Lifetime (US3) or Unlacquered Brass (US3NL), the Emtek keeps the material match.

Several hinges share the word heavy duty or full mortise without being interchangeable with a 4" x 4" square corner residential brass hinge. The Command Access ETH-BB68 and ETM-BB68 are energy transfer hinges that carry wiring through the door, and the ETM-BB68 adds an integrated door position switch, so they belong on an access controlled opening rather than a plain door; the Emtek 96214 is a non-electronic hinge. The Hager 990 STEEL is a full surface prison hinge with a welded tip, which mounts on the face of the door rather than in a mortise. The BEST BB855 is a double weight concealed ball bearing prison hinge in the detention line. None of these drop into a standard residential mortise.

The Emtek 96214 is a plain bearing hinge with no spring mechanism, so it swings free and needs a separate closer. For a door that must return to the frame on the hinge itself, the Stanley Security Spring Hinge Full Mortise, Square Corner, 4.5" x 4.5" is a full mortise square corner spring hinge in a heavy duty rating. It uses a 4-1/2" leaf, so plan on enlarging a mortise cut for the 4" 96214.

The Emtek 96214 is brass through the leaf, not plated steel, which is the usual reason buyers pick it for humid and coastal work, and it is offered in Unlacquered Brass (US3NL) if the finish is meant to patina. Among commercial hinges, the McKinney T2314 Non Ferrous Hinge is a standard weight 5 knuckle non-ferrous hinge rated medium duty, which is the commercial line equivalent of avoiding a steel base in the same conditions.

The Emtek 96214 is a non-electronic hinge with no wire path through the barrel, so an access controlled opening needs a transfer hinge instead. The BEST CECB179-12C is a steel full mortise concealed bearing electrified hinge with a 12-wire quick connect, rated medium duty, and the Stanley CECB1900R54L is a three knuckle concealed bearing concealed conductor hinge, steel full mortise, 4-1/2" by 4-1/2", square corner, left-handed, 4-wire. Count the conductors your lock and monitoring need before choosing between 4-wire and 12-wire, and note the Stanley is handed.

The Emtek 96214 is a residential rated 4" x 4" plain bearing brass hinge, well suited to unit entry and interior doors across a property. Corridor, stair and other doors that see constant use are usually specified with a bearing hinge instead: the Ives 3CB1HW is a steel heavy weight concealed bearing full mortise hinge with 3 knuckles, and the Stanley FBB191 is a 5-knuckle full mortise standard weight hinge at 4.5" x 4.5", rated heavy duty. A two tier standard, the 96214 on unit doors and a bearing hinge on the common area doors, is the usual split.

The Emtek 96214 is a brass hinge in the American Classic style, offered in ten finishes including Flat Black (US19), Satin Nickel (619) and French Antique (US7), which is worth paying attention to on a visible opening. For closet and back of house doors where appearance does not decide the order, the Delaney 3-1/2" x 3-1/2" Bulk Steel Residential Hinges Interior come in pairs with a 5/8" radius corner, and the Delaney 4" x 4" Residential Hinges for Castlegate are offered with a 5/8" radius or square corner in pairs.

The Emtek 96214 has a square shape and square corners in the American Classic style, so the barrel reads as a straight cylinder between the leaves. If the design calls for a squared barrel instead, the McKinney SQ3331 Square Barrel 2-Knuckle Decorative Hinge is a 4-1/2" by 4-1/2" standard duty hinge with a two knuckle squared barrel, a different visual line at the jamb and a larger leaf than the 4" x 4" Emtek.