You may also like
1 INCH BEAM CLAMP,M.IRON,EA
Manufacturer Resources
Product Specs
- Country Of Origin:
- China (CN)
- Jaw Size:
- 29/32 in
- Product Net Depth Length:
- 1-1/4 in
- Product Net Width:
- 1 in
- Product Type:
- Beam clamps
- Selling Unit Of Measure:
- each
- Department:
- Electrical
- Product Group:
- Mounting & Support
- Product Subgroup:
- Clamps
- Product Type2:
- Clamp, Beam
- Product Material:
- Malleable Iron
Steel City 500SC-1 – Frequently Asked Questions
1) What beam flange thickness will the Steel City 500SC-1 beam clamp fit?
The 500SC-1 has a 29/32 inch jaw opening, so it clamps onto beam flanges up to about 29/32 inch thick. Anything thicker than that will not seat in the jaw. Measure the flange edge on your purlin or I-beam before ordering, since flange thickness varies along a tapered flange.
2) Is the Steel City 500SC-1 malleable iron or stamped steel?
Malleable iron. That is a cast body rather than a formed sheet-steel spring clip, so it takes the threaded rod or hanger load in a single rigid piece. It is a bare iron casting, which is why these are normally used indoors or in dry interior structural spaces rather than exposed wet or corrosive locations.
3) How much room does the 500SC-1 beam clamp need on the beam flange?
The clamp body measures 1 inch wide and 1-1/4 inch in net depth/length, so it takes up roughly a square inch and a quarter of flange edge. That matters when you are spacing several clamps close together on the same flange or working next to an existing hanger, deck flute, or fireproofing.
4) What is the actual Steel City part number to order this 1 inch beam clamp?
Order it as Steel City 500SC-1. That is the manufacturer part number on the clamp, a malleable iron beam clamp with a 29/32 inch jaw, sold individually.
5) Should I use a beam clamp like the 500SC-1 or drill the steel for a hanger?
A beam clamp is the choice when you cannot or should not drill or weld the structural steel, which is most commercial jobs. The 500SC-1 grips the flange edge mechanically and gives you a threaded hanger point without touching the member. Drilling is only worth it where the structural engineer has approved holes in the beam, or where flange thickness exceeds the 29/32 inch the jaw will accept.
6) Is the 500SC-1 clamp intended for electrical conduit and fixture hanging?
Yes, it is an electrical-department mounting and support item, used to pick up conduit runs, strut, boxes and fixture drops off structural steel. The malleable iron body and 29/32 inch jaw make it a general-purpose flange clamp rather than a fixture-specific bracket.
How fast can I get the Steel City 500SC-1 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Steel City 500SC-1 come with a warranty?
Absolutely. The Steel City 500SC-1 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Steel City 500SC-1?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Steel City 500SC-1 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.