Metallics QTEKD3 10 x 3/4 in. ...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$50.54
$0.54
Metallics QTEKD3 10 x 3/4 in. 1/4 Hex Head Quadrive Self-Drilling & Tapping Screws - #2 Drill Point - Domestic Steel Zinc - 100qty

Metallics QTEKD3 10 x 3/4 in. 1/4 Hex Head Quadrive Self-Drilling & Tapping Screws - #2 Drill Point - Domestic Steel Zinc - Each

(No reviews yet) Write a Review

Model: QTEKD3
Selected Model is

In Stock (leaves warehouse same day if ordered before 3pm ET)

$50.54
$0.54
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
10 x 3/4 in. 1/4 Hex Head Quadrive Self-Drilling & Tapping Screws - #2 Drill Point - Domestic Steel Zinc - 100qty

  • Features

    • 10 Diameter, 3/4" Length
    • 1/4 Hex Head with Quadrive Drive
    • #2 Drill Point
    • Made in the USA
    • Domestic Steel Zinc Material

Manufacturer Resources

Product Specs

Minimum Purchase:
100 units
Division:
Electrical H1
Fastener Head Type:
Hex
Product Group:
Fasteners
Screw Point Type:
Drill Point
Sub Division:
Electrical-E H2
Department:
Electrical
Product Subgroup:
Screws
Product Material:
Domestic Steel Zinc

Metallics QTEKD3 – Frequently Asked Questions

1) What thickness of steel will a #2 drill point self-drilling screw go through?
The Metallics QTEKD3 uses a #2 drill point, which is the light-gauge point used for drilling and tapping its own hole in thin sheet steel such as studs, track, strut clips and sheet metal boxes. It is not a heavy-gauge point, so for thick structural steel you want a higher-numbered drill point instead.
2) Do I need to pre-drill a pilot hole for the Metallics QTEKD3 screw?
No. It is a self-drilling and self-tapping screw, so the drill point cuts the hole and the threads form their own mating thread in one pass on light-gauge steel. Run it with a 1/4 inch hex driver or nut setter in a screw gun.
3) Are these TEK screws made in the USA for a Buy American job?
Yes. The QTEKD3 is made in the USA from domestic steel with zinc plating, which is what procurement usually needs to see on federally funded or domestic-preference electrical work.
4) What driver do I need for a 1/4 hex head Quadrive screw?
A 1/4 inch hex nut setter drives it, and the Quadrive head also takes a square drive bit if you would rather use a bit tip. The hex head type is the primary drive, and the dual recess lets you switch without swapping to a different screw.
5) Is the QTEKD3 screw long enough for attaching strut or a box to a metal stud?
It is a #10 diameter screw with a 3/4 inch length, so it suits attaching thin brackets, clips, straps and device boxes to light-gauge steel. Add up your material thickness and leave enough point to fully tap through the steel; for thicker stacked material you need a longer screw.
6) Are Metallics QTEKD3 screws OK for outdoor or damp locations?
They are domestic steel with a zinc plating, which is a general indoor and dry-location corrosion finish. For wet, coastal or chemically exposed work, a stainless or hot-dip coated fastener is the better call.
7) What is the Metallics part number for the 10 x 3/4 hex head self-drilling screw?
QTEKD3 is the Metallics part number for the #10 x 3/4 inch, 1/4 inch hex head Quadrive self-drilling and tapping screw with a #2 drill point in zinc-plated domestic steel.
How fast can I get the Metallics QTEKD3 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics QTEKD3 come with a warranty?
Absolutely. The Metallics QTEKD3 is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics QTEKD3?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Metallics QTEKD3 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!