Metallics QDS156 10 x 3/4 in. ...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$50.44
$0.44
Image coming soon

Metallics QDS156 10 x 3/4 in. 1/4 Hex Head Quadrive Sharp Point Tapping Screws - Steel Zinc - Each

(No reviews yet) Write a Review

Model: QDS156

In Stock (leaves warehouse same day if ordered before 3pm ET)

$50.44
$0.44
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
10 x 3/4 in. 1/4 Hex Head Quadrive Sharp Point Tapping Screws - Steel Zinc - 100qty

  • Features

    • 10 Diameter, 3/4" Length
    • Steel Zinc Material
    • Made in the USA
    • Hex 1/4 Head with Hex, slotted, Phillips and square Drive

Manufacturer Resources

Product Specs

Minimum Purchase:
100 units
Division:
Electrical H1
Fastener Head Type:
Hex
Product Group:
Fasteners
Sub Division:
Electrical-E H2
Department:
Electrical
Product Subgroup:
Screws
Product Material:
Steel Zinc

Metallics QDS156 – Frequently Asked Questions

1) What size is the Metallics QDS156 tapping screw?
The QDS156 is a #10 diameter screw, 3/4 inch long, with a 1/4 inch hex head. That short length suits attaching to sheet metal, strut, or thin material where a longer screw would bottom out or punch through behind the substrate.
2) Can I drive the Metallics QDS156 with a Phillips bit instead of a hex driver?
Yes. The Quadrive head takes hex, slotted, Phillips, or square drive, so a 1/4 inch hex driver in an impact gun is the fast option but a Phillips or square bit works when you cannot get a nut setter into a tight spot.
3) Do I need to pre-drill a pilot hole for these hex head tapping screws?
No. The QDS156 is a sharp point tapping screw, so it pierces and taps its own thread in sheet metal and light gauge material without a pilot hole. If you are fastening into heavier plate, a pilot still makes sense because a sharp point is not a self-drilling drill point.
4) Are these screws OK for damp or outdoor electrical work?
The QDS156 is zinc plated steel, which handles indoor and protected locations fine. For exterior exposure, wet locations, or corrosive environments, step up to a stainless fastener instead; zinc plating on steel is a mild corrosion coating, not a marine one.
5) What is the Metallics QDS156 used for on an electrical job?
It is a general purpose electrical fastener: mounting boxes, straps, clamps, plates, and brackets to sheet metal, studs, and light steel. The hex head seats flat against a strap or box ear and takes a nut setter, which is why electricians favour it over a pan head on repetitive runs.
6) How are Metallics QDS156 screws packaged?
They come 100 to a box. One part number, one configuration, so there is no finish or drive option to specify when you order.
How fast can I get the Metallics QDS156 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics QDS156 come with a warranty?
Absolutely. The Metallics QDS156 is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics QDS156?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Metallics QDS156 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!