ACSI 1320-6-2 Pushbutton Switches , Narrow style, 2 LEDs (red & green), 1-3/4" frame mount

The 1320-6-2 is the narrow style version, built for 1-3/4 inch frame mounting, so it goes on the stile or frame face rather than needing a full-width plate. It is also set up for single gang wall mounting, so you can run it either way depending on where you want the release located.

No. The 1320-6-2 is not ADA compliant, so it should not be used where you need an accessible actuator. For that application look at a large push plate with the handicap symbol, such as the RCI 950 Series round push plate in satin stainless with the handicap symbol and momentary switching.

Yes, that is the pairing ACSI calls out for it. The 1320-6-2 release pushbutton is specified for use with the 6100 Common Batch Door System, so if you are building or servicing a 6100 setup this is the matched release station rather than a generic third-party button.

The Trine 342 is the closest match in form factor - it is a narrow style electric door switch, the same mullion/frame-width profile as the ACSI 1320-6-2, which mounts to a 1-3/4 inch frame. The difference to check before you swap is indication: the ACSI 1320-6-2 carries two LEDs, red and green, for status feedback at the door, while the Trine 342 is described simply as a narrow style electric door switch. If the opening relies on a lit red/green status at the button, confirm the indication before substituting.

Go to a single-gang-format button rather than the narrow 1-3/4 inch frame-mount ACSI 1320-6-2. The DynaLock 6115A is a one-pushbutton, 1 gang unit with alternate action, which suits a standard gang box in the wall next to the opening. The Securitron PB3 Series push buttons are another option for standard button locations. The ACSI 1320-6-2 is built for the narrow frame face where a gang box will not fit, so the choice is driven by where the box is, not by the switching.

No - use a dedicated actuator plate for that role. The ACSI 1320-6-2 is not ADA compliant; it is a narrow style release pushbutton for a 1-3/4 inch frame. For a barrier-free actuator, the RCI 950 Series round push plate carries the handicap symbol and is a momentary switch in satin stainless steel, which is the format users expect at an accessible opening. Keep the 1320-6-2 for the staff-side release and specify the push plate separately.

The ACSI 1320-6-2 is a commercial interior-style narrow frame-mount release button with red and green LEDs and no weather rating stated. For an exterior or wet location, the DynaLock 6171 Series is a weatherproof pushbutton with a blank faceplate. You give up the red/green LED indication of the 1320-6-2 and the narrow 1-3/4 inch frame profile, so plan the mounting surface accordingly.

The ACSI 1320-6-2 is a release pushbutton for normal request-to-exit or release duty at the frame. For a marked emergency release, the Securitron EEB emergency exit push button uses interchangeable LED lenses, and the RCI 908 Series electronic exit button is supplied with red EXIT text and maintained operation. Those carry the signage and latching behavior an emergency station needs; the 1320-6-2 is an unmarked narrow frame-mount device.

The 1320-6-2 carries two LEDs, red and green, on the faceplate. They give a visual state indication at the button itself, which is why this one gets specified on release stations where the person at the door needs to see whether the opening is secured or released before pulling. If you don't need indication, a blank illuminated-only or plain button such as the Securitron PB3 covers the same release function without the two-colour readout.

The closest cross-brand equivalent in narrow format is the Trine 342 narrow style electric door switch, which mounts in the same tight frame or stile application. If you want a labelled exit station instead, the RCI 908 Series electronic exit button comes with red EXIT text and maintained operation. Keep in mind neither of those carries the two-colour LED indication or the tie to ACSI's 6100 door system that the 1320-6-2 has.

The 1320-6-2 is not a weatherproof station. It is a narrow frame or single gang wall mount button for interior access control use. For an exterior opening, go with a weatherproof unit such as the DynaLock 6171 Series weatherproof pushbutton.

The ACSI 1320-6-2 gets its indication from two LEDs, red and green, in a narrow style body. If you want illumination in a different body style, the Securitron PB4L Series is a stainless push button with an illuminated halo, and the Securitron PB5 Series is a medium round illuminated push button. Both put light at the button the way the 1320-6-2 does, but in round formats rather than the narrow 1-3/4 inch frame-mount profile, so verify the frame or wall face has room for a round plate.

Match the action to the application. If the opening needs a device that holds its state until pressed again, the DynaLock 6115A is an alternate action pushbutton, the DynaLock 6210 Series palm switches are alternate-action SPDT, and the RCI 919 Series rotary release button is supplied with maintained operation in satin aluminum. The ACSI 1320-6-2 is a release pushbutton with red and green LEDs, so confirm the required switching against the control panel before choosing between it and a maintained device.

No. The DynaLock 6300 Series is an audible annunciator rated 6-28 VDC - it makes a sound to signal a door condition, it does not release the door. The ACSI 1320-6-2 is a release pushbutton with red and green LEDs in a narrow 1-3/4 inch frame-mount body. They are often on the same door and the same drawing, which is why they get confused, but the 6300 is a companion device, not a substitute.

A large-surface actuator is easier to hit than the narrow ACSI 1320-6-2, which is a narrow style button on a 1-3/4 inch frame. The DynaLock 6210 Series palm switch buttons are alternate-action SPDT and present a palm-sized target, and the RCI 950 Series round push plate is a momentary switch in satin stainless steel. Both suit carts, gloves, and high-traffic staff doors; the 1320-6-2 remains the choice where only the frame face is available.

Commercial. The 1320-6-2 is an electronic access control device in ACSI's 1300 Series, specified for commercial openings. It is a low voltage release switch wired into a door control circuit, not a line-voltage residential switch.

It is a release pushbutton for the 6100 Common Batch Door System, used to release the opening on press. If your application specifically needs an alternate action button that stays latched until pressed again, that is a different device, and DynaLock's 6115A one-button single gang unit is an alternate action switch.

They are different control types. The RCI 909 Series is a flush mount momentary rocker switch rated 250VAC 10A in a beige finish - a rocker actuator with a line-voltage-capable contact rating. The ACSI 1320-6-2 is a narrow style frame-mount release pushbutton with red and green LED indication. If the opening was specified for a lit button at the frame face, the rocker will not give you the red/green status or fit the 1-3/4 inch frame profile.