You may also like
B-Line Eaton series strut fittings and accessories, 1.62" Height, 7.25" Length, 1.62" Width, .76lbs, Aluminium, Four hole splice plate, Aluminum
Model: BLN-B341AL
Eaton B-Line series strut fittings and accessories, 1.62" Height, 7.25" Length, 1.62" Width, .76lbs, Aluminium, Four hole splice plate, Aluminum
B-LINE
$5,759.59
B-Line Eaton series strut fittings and accessories, 1.62" Height, 7.25" Length, 1.62" Width, .76lbs, Steel, Four hole splice plate | Pre assembled, DU
Model: BLN-B341PAGRN
Eaton B-Line series strut fittings and accessories, 1.62" Height, 7.25" Length, 1.62" Width, .76lbs, Steel, Four hole splice plate | Pre assembled, DURA GREEN
B-LINE
$9,000.07
B-Line Eaton series strut fittings and accessories, 1.62" Height, 7.25" Length, 1.62" Width, .76lbs, Steel, Four hole splice plate | Pre assembled, El
Model: BLN-B341PAZN
Eaton B-Line series strut fittings and accessories, 1.62" Height, 7.25" Length, 1.62" Width, .76lbs, Steel, Four hole splice plate | Pre assembled, Electro-plated zinc
B-LINE
$8,940.27
B-Line Eaton series strut fittings and accessories, 1.62" Height, 3.25" Length, 1.62" Width, .34lbs, Steel, Two hole splice plate, Hot-dipped galvaniz
Model: BLN-B340HDG
Eaton B-Line series strut fittings and accessories, 1.62" Height, 3.25" Length, 1.62" Width, .34lbs, Steel, Two hole splice plate, Hot-dipped galvanized
B-LINE
$3,284.86
B-Line Eaton series strut fittings and accessories, 3.77" Height, 1.62" Length, 1.62" Width, .73lbs, Steel, Three hole cup support, Hot-dipped galvani
Model: BLN-B398-1HDG
Eaton B-Line series strut fittings and accessories, 3.77" Height, 1.62" Length, 1.62" Width, .73lbs, Steel, Three hole cup support, Hot-dipped galvanized
B-LINE
$10,755.33
Eaton B-Line series strut fittings and accessories, 1.62" Height, 7.25" Length, 1.62" Width, .76lbs, Steel, Four hole splice plate, Hot-dipped galvanized
Manufacturer Resources
Product Specs
- Certifications:
- Not Applicable
- Product Height:
- 1.62 in
- Product Length Depth:
- 7.25 in
- Product Weight:
- .76 lb
- Product Width:
- 1.62 in
- Department:
- Electrical
- Product Group:
- Panels & Plates
- Product Subgroup:
- Plates
- Product Type:
- Four hole splice plate
- Product Finish:
- Hot-dipped galvanized
- Product Details:
- Four hole splice plate
- Product Material:
- Steel
B-LINE B341HDG – Frequently Asked Questions
1) What is the Eaton B-Line B341HDG four hole splice plate used for?
The B341HDG is a four hole splice plate for joining two lengths of strut channel end to end. It bolts across the joint, with two holes landing in each channel run, so a continuous strut run can be extended without cutting a new full-length piece. It is steel with a hot-dipped galvanized finish.
2) Will a B-Line B341HDG splice plate fit standard 1-5/8 inch strut channel?
The plate measures 1.62 inches wide by 1.62 inches high by 7.25 inches long, so the face matches the 1-5/8 inch nominal width of standard strut channel. It lays flat against the channel face and spans 7.25 inches across the joint, giving roughly half that bearing length on each side of the splice.
3) Do I need to order bolts and channel nuts separately for a B-Line B341HDG splice plate?
Yes. The B341HDG is the plate only, at .76 lb of galvanized steel. You supply the hardware to fasten it: four bolts with matching channel nuts, one set per hole, sized to the strut you are splicing. Match the hardware finish to the plate if the run is outdoors.
4) Is the B341HDG splice plate suitable for outdoor or damp locations?
Hot-dipped galvanized steel is the finish, which is the coating normally specified for exterior, wet, or corrosive-duty strut runs such as rooftops, parking structures, and mechanical yards. Plain electro-galvanized fittings are the indoor, dry-location choice.
5) Should I use a four hole splice plate or a longer piece of strut instead?
A four hole splice plate makes sense when the run has to be extended in place, when stock lengths do not reach, or when the assembly has to be field-adjusted or broken down later. If the span is unsupported and carries load at the joint, a continuous length of channel is the stronger detail. The B341HDG gives a 7.25 inch splice with two bolt holes per side, so keep a support near the joint rather than spanning across it.
6) What is the exact part number to order the B-Line hot-dipped galvanized four hole splice plate?
Order Eaton B-Line part number B341HDG. The HDG suffix denotes the hot-dipped galvanized finish on the steel plate.
How fast can I get the B-LINE B341HDG delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the B-LINE B341HDG come with a warranty?
Absolutely. The B-LINE B341HDG is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the B-LINE B341HDG?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the B-LINE B341HDG from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.