Calibre Door Closers UH1200 4"-12" CTC Universal Multi-Sized Offset Pull Handle
Features:
- Standard 12" CTC Offset Pull Handle with Press Fitting End Brackets.
- On site adjustment to match any existing installation centerline hole dimensions from 12" CTC to 4" CTC.
- Stanchion Bar is 6063 T5 extruded aluminum with Class 1 anodized electrolytic finish.
- Press fitting End Brackets are a 380 aluminum die cast alloy with a high quality thermosetting polyester powder coated finish.
- Universal 1/4-20 fasteners are included for Thru-Bolt, Concealed and Back-to-Back installations.
- Includes 2 each countersunk trim washers.
- Finish: Aluminum with Black End Brackets
Resources
Manufacturer Resources
Product Specs
- Subcategory:
- Handlesets
- Series:
- CA/Hardware Series
- Product Group:
- Mechanical Locks
- Product Subgroup:
- Handlesets
- Product Type:
- Offset Pull Handle
- Commercial/Residential:
- Commercial
- Product Model:
- UH1200
- Door Hand Direction:
- Field Reversible
- Product Category:
- Mechanical Locks
- Department:
- Door Hardware
Calibre Door Closers UH1200-AL – Frequently Asked Questions
1) Will the Calibre UH1200 pull handle match my existing door's hole spacing, or do I have to drill new holes?
No new drilling in most cases. The UH1200 ships as a 12 inch center-to-center offset pull, and the press fitting end brackets adjust on site anywhere from 12 inch CTC down to 4 inch CTC to land on an existing centerline hole pattern. That is the whole point of the design: one part covers the range instead of ordering a fixed-CTC pull and hoping it lines up with what the last handle left behind.
2) What mounting hardware comes with the Calibre UH1200 offset pull, and how can it be installed?
Universal 1/4-20 fasteners are included, covering thru-bolt, concealed, and back-to-back installation. Two countersunk trim washers come in the box as well. So whether you are mounting the pull alone with concealed fasteners, thru-bolting the door, or pairing it back-to-back with a push bar or a second pull, the fastener set is already in the carton.
3) I am replacing a broken pull on an aluminum storefront door and do not know the hole spacing. What should I order?
The UH1200 is the part to reach for when you cannot get out to measure first. Because the end brackets press fit and adjust from 12 inch CTC down to 4 inch CTC, the installer sets the spacing at the door instead of you having to confirm the old pattern before the order goes out. Bring the included 1/4-20 fasteners and it covers thru-bolt or concealed mounting depending on what the door prep allows.
4) Does the Calibre UH1200 pull handle have a hand, or does one part work on left and right doors?
One part covers both. The UH1200 is field reversible, so the same pull works on a left hand or right hand opening without ordering a specific hand. For a property manager restocking pulls across a building, that means one line item instead of two.
5) What finishes does the Calibre UH1200 universal pull handle come in?
Two: AL aluminum and DU storefront bronze. The stanchion bar is 6063 T5 extruded aluminum with a Class 1 anodized electrolytic finish, and the die cast end brackets carry a thermosetting polyester powder coat. On the aluminum version the brackets are black, so the pull reads as a two-tone piece rather than a single uniform color, which matters if you are trying to match adjacent openings in a storefront elevation.
6) Is the Calibre UH1200 pull built for commercial traffic or is it a residential handle?
Commercial. The bar is 6063 T5 extruded aluminum, and the press fitting end brackets are a 380 aluminum die cast alloy with a powder coated finish, which is the construction used on storefront and entrance pulls rather than a light residential handle. It is rated commercial in the product data.
7) Can the Calibre UH1200 be mounted back-to-back with another pull on the same door?
Yes, the included 1/4-20 fastener set covers back-to-back installations, so two UH1200 pulls can go through the same holes on opposite faces of the door. Order two handles; the fasteners for the back-to-back arrangement come with them.
8) What is an offset pull handle and when would I use one instead of a straight pull?
An offset pull stands the grip away from the door face on end brackets (stanchions), which leaves clearance for a gloved hand and keeps knuckles off the door or the glass stop. On aluminum storefront and glass entrances that offset is what makes the pull usable next to a narrow stile. The UH1200 is that style, with a 6063 T5 extruded aluminum stanchion bar and press fitting brackets, adjustable from 12 inch down to 4 inch center-to-center to match whatever pattern is already drilled.
How fast can I get the Calibre Door Closers UH1200-AL delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Calibre Door Closers UH1200-AL come with a warranty?
Absolutely. The Calibre Door Closers UH1200-AL is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Calibre Door Closers UH1200-AL?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Calibre Door Closers UH1200-AL from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.