Delaney Mircet - Grade 2 Privacy Leverset

No key. The Mircet is a privacy function lockset: the lock is operated from the inside only, with a small pin hole on the outside lever so the door can be released from the corridor side in an emergency. That is the standard setup for bedroom and bathroom doors.

Not as an entry lock. The Mircet is a residential Grade 2 privacy set with no cylinder, so it suits bedroom and bath doors. For unit entry doors you need a keyed entry or storeroom function lockset instead.

No indicator on the Mircet, just a plain privacy turn inside and a pin hole outside. If you need a visual occupancy status, the Cal-Royal INDLEV-20 is a privacy indicator leverset with a red/green occupancy indicator, listed with 2-3/8 inch and 2-3/4 inch backsets and an adjustable 1-3/8 inch to 1-3/4 inch door thickness range. That one is the pick for restrooms in offices, clinics, and schools.

The Delaney Mircet privacy leverset uses the standard arrangement: an interior locking mechanism with a small pin hole on the exterior side to release it. If you need staff or visitors to see occupancy at a glance, the Cal-Royal INDLEV-20 is a privacy indicator leverset with a red/green occupancy indicator. That makes it the choice for public or shared restrooms, while the Mircet suits bedroom and bath doors where the pin release is enough.

The Mircet privacy leverset is classified as residential and carries a Grade 2 rating, which suits apartment bedrooms and bathrooms. For an opening you are treating as commercial duty, the Cal-Royal INDLEV-20 privacy leverset is listed as standard duty commercial grade. Both are privacy function levers, so the difference is the duty classification rather than how the lock behaves.

Handing isn't an ordering decision here. The Mircet is a cylindrical bored lockset, and bored privacy levers of this type are reversible on the door, so the same set works on a left or right hand door.

Both. It ships with combination screws that suit wood or metal door mounting, so you don't need a separate fastener pack for a hollow metal leaf.

Projection is 2-3/8 inches off the face of the door, with a rose length of 2.5625 inches. Worth checking if the door swings into a tight corner or beside a wall return where a lever could strike.

Yes for residential turnover traffic. Grade 2 is the middle ANSI/BHMA duty tier and the Mircet is built for residential use, which covers bedroom and bath doors in single family and small multi-family. For a high-traffic public restroom, step up to a commercial duty set such as the Cal-Royal INDLEV-20.

Usually yes. The Mircet is a cylindrical bored set, the same prep family as a standard residential knob, so it goes into an existing 2-1/8 inch cross bore with a 1 inch edge bore in most cases. Match the existing backset (2-3/8 or 2-3/4 inch) when you order the latch.

Backset and projection are different measurements, so check the door prep before ordering. If you need a privacy lever that covers both common preps in one part, the Cal-Royal INDLEV-20 is offered for 2-3/8 inch and 2-3/4 inch backset and adjusts for door thickness from 1-3/8 inch to 1-3/4 inch, which is useful when a building has mixed preps across the doors.

The Mircet is a cylindrical bored lockset in privacy function, meaning it locks from the inside only and releases through the exterior pin hole - there is no key cylinder. Swapping in a keyed or passage lever changes how the door secures even where the bore is shared, so match on function first. Within privacy function, the Cal-Royal INDLEV-20 is the alternative, differing by adding a red/green occupancy indicator.

Two: US15 Satin Nickel and US19 Black. If you're standardizing a house or a block of units, both are common enough to match hinges and stops from most lines.

The Delaney Mircet privacy leverset comes in US15 Satin Nickel and US19 Black, so it matches decorative schemes on bedroom and bath doors. The Cal-Royal INDLEV-20 is specified around its privacy indicator function and backset range rather than a matching decorative finish set, so if finish consistency across a unit is the driver, keep the openings on the Mircet and reserve the INDLEV-20 for doors that genuinely need the occupancy indicator.