Deltana FRP175 Flush Ring Pull, 1-3/4" x 1-3/8"

The FRP175 face measures 1-3/4 x 1-3/8 inches, so the mortise pocket is cut to that footprint and the pull sits flush with the door face. It is a small pull, sized for a pocket door edge or a cabinet-scale sliding panel rather than a full-width barn door grip. If you need a longer finger recess, Emtek's 2201 rectangular brass flush pull runs 1-3/4 x 4 inches and the Emtek 2205 Brass #8 runs 1-7/8 x 5 inches.

Mounting hardware is in the bag. Each FRP175 ships individually poly bagged with its mounting hardware, sold one per unit, so there is nothing else to order to install it. Plan on routing the recess yourself; the pull is the finish part only.

The Deltana FRP175 is the ring pull. It is a flush ring pull in solid brass at 1-3/4 by 1-3/8 inches, with a hinged ring seated in the cup that swings up for a full-hand grip and drops flush when released. The Emtek Rectangular 2201 and Modern Rectangular 220304 are both rectangular brass flush pulls at 1-3/4 by 4 inches, gripped by reaching into the recess rather than by a ring. For a heavy pocket or barn slab that a fingertip cannot start moving, the ring on the FRP175 is what gives the pull real leverage.

The Deltana FRP175 has a 1-3/4 by 1-3/8 inch footprint, which is a compact pocket in the edge or face of the slab. For a larger grip area, the Emtek 2205 Brass #8 flush pull runs 1-7/8 by 5 inches in brass, and the Emtek 2201 Rectangular and 220304 Modern Rectangular are both 1-3/4 by 4 inches. The largest cutout of the group is the Emtek 220404 Rustic Modern Rectangular sandcast bronze at 2 by 4 inches, the only one that needs a mortise wider than 1-7/8 inches. Route to whichever one you order, because the FRP175 pocket will not accept any of them.

Nine finishes across the FRP175: PVD Polished Brass, Polished Brass, Antique Brass, Oil Rubbed Bronze, Brushed Nickel, Antique Nickel, Polished Chrome, Brushed Chrome, and Paint Black. If you are matching existing hardware in a building, PVD Polished Brass is the one to specify where the pull sees heavy hand contact or exterior exposure, since the PVD coating holds its color rather than living finishes that change with wear.

Solid brass, both the material and the substrate on the FRP175, not a plated zinc or steel casting. That matters on a recessed pull because the ring gets pulled on at an angle and a thin plated part deforms at the pivot. It also means the finish is applied over brass, so wear-through at the edges shows brass rather than a different base metal.

A ring pull like the FRP175 gives you a hinged or lifting ring you can hook a finger through and get real pulling force on, which is what you want on a heavy pocket door or one that has to be pulled from the closed position. A plain rectangular cup, like the Emtek 220304 Modern Rectangular or the sandcast bronze Emtek 220404, gives you a recessed finger pocket only, which is a cleaner look but less grip. The Deltana ring is also the smaller footprint at 1-3/4 x 1-3/8 inches, so it routs into a narrower stile than the 4-inch Emtek cups.

Pricing and packing on the FRP175 are per each, one pull per poly bag. A pocket door normally takes two, one per face, so order in pairs. A pair of doors meeting in the middle takes four if both faces are pulled, or two if only the room side is.

No. The Emtek 220404 Rustic Modern Rectangular is sandcast bronze at 2 by 4 inches, while the Deltana FRP175 is solid brass at 1-3/4 by 1-3/8 inches and the Emtek 2201, 220304, and 2205 are brass at 1-3/4 by 4, 1-3/4 by 4, and 1-7/8 by 5 inches. Sandcast bronze is a poured body with an irregular surface, so it will not read as a match next to machined brass hardware, and the 2 inch width is the widest mortise in the group. Treat it as a different specification rather than a like-for-like swap.

The Deltana FRP175 is rated for commercial use, built in solid brass at 1-3/4 by 1-3/8 inches, and ships in an individual poly bag with its mounting hardware, so a crew standardizing across a floor of pocket doors can order one part number in one finish and fit them all. Its ring gives a full-hand grip, which holds up better than a fingertip pocket where doors are cycled all day. If the design calls for a longer recess instead, the Emtek 2205 Brass #8 is a brass flush pull at 1-7/8 by 5 inches and the Emtek 2201 Rectangular is 1-3/4 by 4 inches, both of which need a larger mortise than the FRP175.

Paint Black is one of the nine FRP175 finishes. Note it is a painted black over solid brass rather than a plated or oxidized black, so touch-up on a nicked edge is paint. For a black that is inherent to the metal rather than a coating, a sandcast bronze pull such as the Emtek 220404 is the other direction to look, though it is a larger 2 x 4 inch cup.