Deltana K4474 Colonial Wire Pull, 4"

The K4474 is a 4 inch Colonial wire pull, so it lines up with cabinets already drilled on a 4 inch pattern. Wire pulls of this style mount through two holes at the ends of the bow, and the stated size for this model is 4 inches. If your existing drawer fronts were bored for a different spacing, you would either need to re-drill or move to a pull sized to that spacing.

It's classed as a residential pull, so for high-traffic institutional casework, guest room millwork, or commercial kitchens it isn't the right pick. For that kind of duty, look at a Trimco 553 or 562 Series drawer pull, which are catalogued as commercial drawer pulls, or an Orca CK-12001 T-pull bar in steel. The K4474 is meant for residential cabinetry and light-use built-ins.

Two other 4 inch options sit alongside it. The Omnia 1968/102 is a forged solid brass modern pull at 4 inch center-to-center, so it's the same spacing in a squarer, contemporary profile instead of the K4474's traditional bowed wire shape. The Trimco 562 Series drawer pull is offered in 4 inch center-to-center as well, along with 3-1/2 inch and 96mm. The Schaub 10011 is a 4 inch center-to-center Sabre edge pull, but that one mounts on the edge of a door or drawer front rather than on the face, so it isn't a drop-in for a face-mounted pull.

The Omnia 1968/102 Modern Cabinet Pull is the nearest brass-for-brass alternative at the same nominal 4 inch dimension. Both are solid brass pulls: the K4474 is solid brass in a 4 inch size, and the Omnia 1968/102 is forged solid brass with 4 inch center-to-center spacing. The difference to check before you order is which dimension the 4 inch refers to. The K4474 is a Colonial wire pull described by its 4 inch length, so measure your existing hole spacing against the pull itself rather than assuming the two drill to the same centers. The styling also differs: the K4474 is a traditional Colonial wire profile, while the 1968/102 is from Omnia's modern series.

For a retrofit onto holes already drilled at 4 inch centers, the Trimco 562 Series drawer pull is the one to specify, because it is offered in a 3-1/2 inch, 4 inch, and 96mm center-to-center range and the 4 inch option matches your existing bore. The Omnia 1968/102 also carries 4 inch center-to-center spacing. The Deltana K4474 Colonial Wire Pull is sized as a 4 inch pull rather than by drilled centers, so if you are replacing pulls one for one without redrilling, confirm the mounting centers on the pull you are removing first. If your cabinets have a mix of spacings across a unit, the Trimco 562 covering three center dimensions in one series lets you standardize on a single family.

No. The two share a 4 inch dimension but they are different kinds of hardware and mount differently. The Schaub 10011 is a 4 inch center-to-center edge pull, meaning it is designed to be applied at the edge of a door or drawer front, and Schaub lists its function as an edge pull. The Deltana K4474 is a Colonial wire pull, a face-mounted pull in solid brass at a 4 inch size. Ordering the 10011 expecting a face-mounted wire pull will leave you with hardware that does not sit where your existing holes are. Schaub's Sabre edge pull range also runs to 3 inch and 5 inch center-to-center in the 10010 and 10012 if an edge pull is in fact what the job calls for.

Nine finishes: Polished Brass, PVD Polished Brass, Antique Brass, Antique Nickel, Brushed Nickel, Polished Chrome, Brushed Chrome, Oil Rubbed Bronze, and Paint Black. The PVD Polished Brass is the one to specify if you want the brass look without the ongoing polishing that a lacquered brass finish needs, and Paint Black is the flat painted option rather than a plated one.

Solid brass. Both the material and the substrate on the K4474 are brass, so the finish sits on a brass body rather than on a zinc or steel casting. That matters on a pull that gets handled every day: a worn spot on a plated zinc part shows a different colored metal underneath, and it also means the antique and oil rubbed finishes wear in rather than wear through to something obviously wrong.

No. At 4 inches, the K4474 is a cabinet and drawer pull, not an appliance pull. For a refrigerator or dishwasher panel you want something in the 8 inch range or longer, like the Schaub 79-8 Steamworks 8 inch pull, which is catalogued as an appliance pull.

If the traditional Colonial wire profile is more detail than the unit needs, the Orca Hardware CK-12001 T-Pull Bar is the plainer choice. It is a steel pull with a 2 inch bar width in satin nickel, so it is a single finish and a single form rather than a styled pull in a range of finishes. The K4474 is solid brass and is stocked in nine finishes including polished brass, oil rubbed bronze, brushed nickel, antique nickel, paint black, polished chrome, and brushed chrome, which is what you want when the pull has to match existing decorative hardware. For a turnover where the goal is uniform, unfussy hardware across every door and drawer, the steel T-pull bar keeps the fleet consistent; where the cabinetry is period or the brass finish has to be matched, stay with the K4474.

For an appliance front, specify a pull built for that duty instead. The Schaub 79-8 Steamworks 8 inch cabinet pull is designated an appliance pull and is 8 inch, which is the length range a refrigerator or panel-ready dishwasher front normally takes. The Deltana K4474 is a 4 inch Colonial wire pull rated for residential use, which suits cabinet doors and drawers rather than a full-height appliance panel. If you want the appliance pull and the surrounding cabinet pulls to read as one set, plan the appliance opening around the Schaub 79-8 and keep the K4474 on the cabinetry.

Several modern-profile pulls cover the same job. Omnia's modern cabinet pull series gives you a range of projections to pick from: the 1969 and the 1971 are forged solid brass at 1-3/16 inch projection, and the 1970 is forged solid brass at 1-1/4 inch projection, so you can match how far the pull stands off the face. The Emtek Bar Cabinet Pull from the Schaub collection is a straight bar form. All of these are pulls in the same duty class as the Deltana K4474 Colonial Wire Pull, which is the traditional wire profile in solid brass. If your cabinet fronts are close to a wall or an adjacent door swing, the stated Omnia projections are the number to design against.

Only if you are willing to redrill. The Orca Hardware CK-15030 and CK-16030 Bachelor Collection pieces are round cabinet knobs at 1-1/4 inch diameter, and the CK-17025 Blackcomb Collection piece is a square cabinet knob at 25mm diameter. All three are single-post knobs, while the Deltana K4474 is a 4 inch pull with two mounting points. Swapping a two-hole pull for a single-post knob leaves an unused hole in the drawer front. Knobs are the right call when you are starting from undrilled fronts or already have single-bore cabinetry; if the fronts are drilled for a pull, stay with a pull.

Yes. The Trimco 553 Series drawer pull is a 3 inch center-to-center pull, and the Trimco 562 Series includes a 3-1/2 inch center-to-center option, both shorter than the 4 inch Deltana K4474 Colonial Wire Pull. Schaub's Sabre range also runs down to the 10010 at 3 inch center to center if an edge-mounted pull suits the front. On narrow drawers and small doors the shorter center dimension keeps the pull inside the rail; on wider drawer fronts the 4 inch K4474 stays visually in proportion. If a run mixes narrow and wide fronts, the Trimco 562 Series spans 3-1/2 inch, 4 inch, and 96mm in one series so the whole run reads as one family.

Yes. The K4474 is a face-mounted cabinet pull, and a 4 inch wire pull works on drawer fronts and on door stiles alike. On a narrow door stile, the thing to check is that the stile is wide enough to take the pull's mounting holes without crowding the edge, since a 4 inch pull needs its two screws set in from the ends of the bow.

If you want a knob to sit beside the K4474 wire pulls, the Orca Bachelor Collection round cabinet knob at 1-1/4 inch diameter or the round ring knob in the same collection are the knob options here, and the Blackcomb square knob at 25mm if you want a squared profile. Match on finish rather than assuming a family match, since the K4474 is a Deltana part and those knobs are a different brand.

Order the K4474 by model and finish. Finish is the only choice to make, and it's sold each, so the quantity you enter is the number of individual pulls, not pairs or packs. Count your drawer fronts and doors and order one per opening.