You may also like
DynaLock 6700 Series Pushplates
Model 6753 Recessed Single Gang, Momentary SPDT
6700 & 6800 Series Pushplates are heavy duty egress controls machined
from solid aluminum with engraved “PUSH TO EXIT” signage. Multiple
switching configurations and finishes are available. Narrow recessed models
are specifically designed for installation in aluminum store front frames,
requiring minimal cut-out/preparation. All momentary models feature “all
active” operation. Consult factory for special engraving.
Standard finish - Satin Aluminum US28
PTD Contact Rating: 10 A @ 125VAC
All Others: 6 A @ 125VAC
Manufacturer Resources
Product Specs
- Subcategory:
- Push Buttons
- Series:
- 6700
- Product Group:
- Electronic Access Controls
- Product Subgroup:
- Sensors, Switches, Relays and Timers
- Product Type:
- Switches / Push Buttons
- Commercial/Residential:
- Commercial
- Electronic:
- Yes
- Duty Level:
- Heavy Duty
- Product Model:
- 6753
- Product Finish:
- Satin Aluminum (US28)
- Product Category:
- Electronic Access Controls
- Department:
- Door Hardware
DynaLock 6753 US26 – Frequently Asked Questions
1) Does a momentary SPDT exit pushplate let me wire both a release and a signal at the same time?
An SPDT switch gives you one common with a normally closed and a normally open contact, so you can break a maglock power path and simultaneously trigger a shunt, timer, or alarm signal from the same press. Momentary means the contacts transfer only while the plate is pressed and then return, which is the normal choice for request-to-exit release on an access controlled door. If you need the switch to stay latched until it is reset, a maintained device such as the RCI 908 Series exit button or the RCI 919 Series rotary release is the right type instead.
2) What is a comparable narrow switch to the DynaLock 6753 for an aluminum storefront frame?
The DynaLock 6753 is a recessed single gang momentary SPDT pushplate, and the narrow recessed 6700 models are designed for aluminum store front frames with minimal cut-out preparation. The closest narrow-profile alternative is the Trine 342 narrow style electric door switch, which is also built for the narrow stile application. Both mount into the tight stile of a glass front door; the DynaLock is machined from solid aluminum with engraved PUSH TO EXIT signage.
3) For an emergency release application, is the DynaLock 6753 the right choice or should I specify something else?
The 6753 is engraved PUSH TO EXIT and is intended as a heavy duty egress control, not as a marked emergency release. When the code official or spec calls for emergency release labeling, the ACSI 1320-1-MOM-ER is a pushbutton switch marked Emergency Release, and the Securitron EEB is an emergency exit push button with interchangeable LED lenses. DynaLock notes special engraving is available by consulting the factory if you want to keep the 6753 plate format.
4) I need a maintained switch instead of momentary - what should I use in place of the DynaLock 6753?
The 6753 is a momentary SPDT pushplate, and all momentary 6700 models feature all active operation, so contact is only made while the plate is pressed. If the job needs the switch to hold its state, the RCI 908 Series electronic exit button with red EXIT text is a maintained operation device, and the RCI 919 Series rotary release button is also maintained and offered in satin aluminum. Choose based on whether you want a push button or a rotary release at the opening.
5) What looks like a substitute for the DynaLock 6753 but will not work the same way?
The ACSI 1310-1 mortise keyswitch sits in the same access control family but is key-operated rather than a push device, so it is for authorized release, not free egress. The RCI 909 Series flush mount momentary rocker switch is momentary like the 6753 but is a rocker rather than an engraved pushplate. And the RCI 950 Series round push plate carries a handicap symbol rather than PUSH TO EXIT text, which changes what the opening is signed for.
6) Does the DynaLock 6753 come already marked for egress, or do I need a separate sign?
The plate is engraved "PUSH TO EXIT" as standard, machined into the solid aluminum face, so no applied label or separate sign is needed at the button. DynaLock will do special engraving on request through the factory. If you need a handicap symbol instead of exit text, the RCI 950 Series round push plate carries the handicap symbol.
7) What finishes can I get on the DynaLock 6700 Series pushplate to match the rest of my door hardware?
Eight finishes: Satin Aluminum US28 (the standard), Bright Brass US3, Satin Brass US4, Light Bronze US10, Dark Bronze US10B, Medium Bronze US13, Black Satin US19, and Bright Chrome US26. For dark anodized storefront the US10B or US19 plates blend in; US28 is the usual match for clear anodized aluminum.
8) Is the 6753 pushplate heavy duty enough for a high traffic commercial exit?
It is a commercial, heavy duty egress control machined from solid aluminum rather than a stamped or plastic faceplate, which is why DynaLock positions the 6700 and 6800 Series as heavy duty. For a school corridor, hospital, or retail entry where the plate gets hit hundreds of times a day, a solid machined plate holds up better than a molded button housing.
9) What is the difference between this recessed DynaLock plate and a surface mounted exit button?
The 6753 is a recessed single gang device, so it sits flush in a cut-out in the frame or wall and leaves nothing projecting to be grabbed or damaged, but it requires prep in the frame. A surface or flush mount button, such as the Securitron PB3 Series push button or the Trine 342 narrow style electric door switch, is the route when you cannot cut the frame or you are mounting to an existing box. Illuminated options like the Securitron PB4L or PB5 are the choice when the button needs to be found in the dark.
10) Is the Securitron PB3 an equivalent to the DynaLock 6753 pushplate?
They are both push switches for access control release, but they are not the same form factor. The DynaLock 6753 is a recessed single gang pushplate machined from solid aluminum with engraved PUSH TO EXIT text, sized to drop into a single gang recess. The Securitron PB3 is a push button rather than an engraved plate. If the drawing calls for a labeled egress plate, the 6753 matches that intent; if a plain button is acceptable, the PB3 is the simpler device.
11) What should I use instead of the DynaLock 6753 if the release button needs to be illuminated?
The DynaLock 6753 is a non-illuminated engraved aluminum pushplate offered in finishes including satin aluminum US28, dark bronze US10B and bright chrome US26. For a lit device, the Securitron PB4L has an illuminated halo with a stainless push button, and the Securitron PB5 is a medium round illuminated push button. Both trade the engraved PUSH TO EXIT plate for a visual indication at the door.
12) I need an accessible actuator at the door - does the DynaLock 6753 cover that or do I need a different plate?
The DynaLock 6753 is engraved PUSH TO EXIT, so it reads as an egress control rather than an accessibility actuator. If the opening needs the accessibility marking, the RCI 950 Series round push plate carries a handicap symbol and is a momentary switch in satin stainless steel. Use the 6753 where a labeled egress plate is wanted and the 950 where the door is signed for accessible operation.
13) Do all the momentary DynaLock 6700 pushplates work no matter which way they are mounted?
Yes. Every momentary model in the 6700 and 6800 Series uses "all active" operation, so the plate releases when pressed anywhere on its face. That matters on a narrow storefront stile where the plate may be mounted vertically and the user pushes near an edge rather than dead center.
14) I need key control on the door, not a push to exit plate. What should I be looking at?
A pushplate like the 6753 is a free-egress release anyone can operate, so it will not give you authorized-only control. For key operated switching on the same kind of access control circuit, the ACSI 1310-1 mortise keyswitch is the device type you want. Many jobs use both: keyswitch on the secure side, momentary exit plate on the egress side.
How fast can I get the DynaLock 6753 US26 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the DynaLock 6753 US26 come with a warranty?
Absolutely. The DynaLock 6753 US26 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the DynaLock 6753 US26?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the DynaLock 6753 US26 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.