Emtek 2255 Brass Wall Bumper with Regular Rosette

Yes. The 2255 is a brass wall bumper built with the regular rosette, so it carries the same 2-3/4 inch round rosette profile used across Emtek's trim and matches on any of the rosette styles. If you are trying to keep a hallway looking consistent, this is the bumper that reads as part of the same set rather than a generic stop screwed to the wall.

No. The 2255 is a residential-rated brass bumper. For corridors, classrooms, or anything taking traffic all day, go to a heavy duty commercial wall stop instead: the Ives WS11 or the Ives WS33/WS33X both use a replaceable rubber bumper and are rated heavy duty. If the door needs to be held open as well as stopped, the Ives WS20 is a manual wall holder with a hinged strike, and the WS40 is an automatic wall holder.

The Emtek 2255 is a brass wall bumper built for residential use, so for a corridor or stairwell door that gets hit hundreds of times a day, step up to the Ives WS11, a heavy duty wall stop with a replaceable rubber bumper that mounts to drywall or masonry. The Ives WS33 is the other heavy duty wall stop in the same family, also with a replaceable rubber bumper. The practical difference for a facility is the bumper itself: on the Ives stops the rubber is a replaceable part, so a worn tip is a service item rather than a reason to pull the whole stop off the wall.

A wall bumper like the 2255 only works when the door swings into a wall within reach of its projection. When the wall is out of reach, or there is no wall at all behind the swing, move to a floor or hinge mounted stop: the Delaney 3 inch HD rigid door stop and the Delaney 3 inch spring door stop both mount to the floor and take the door at its edge rather than at the wall. The rigid version has no give; the spring version flexes on contact. If the wall is reachable but the standard projection is short, the ABH RM Series and ABH RMS Series wall door stops come in multiple length options.

Five: Flat Black Bronze (FB), Oil Rubbed Bronze (US10B), Flat Black (US19), Satin Brass (US4), and French Antique (US7). Those US numbers are the standard finish codes, so if your door levers are already spec'd US10B or US4 you can order the bumper to the same code and it will read as a match.

It is rubber tipped, which is what takes the hit from the lever or knob and keeps the door face from getting dented. The brass body spreads the load on the wall side, so it stops the doorknob punching a hole in the drywall too.

The rosette measures 2-3/4 inches in diameter, so it covers a wider footprint than most small round bumpers and will often sit over the marks left by a previous stop. It will not cover a large hole. For that, the Delaney 2-1/8 inch hole plate metal cover is the piece made to close one off.

The 2255 rosette is 2-3/4 inches across. If that is too much face for the wall, the Delaney 2-1/4 inch concave wall bumper is a smaller round bumper of the same type. If instead you need to reach further off the wall because the door swings past baseboard or trim, the ABH RM Series and RMS Series wall stops are offered in multiple lengths.

Both are holders rather than plain bumpers, so either changes how the opening behaves compared with the 2255, which simply stops the door. The Ives WS20 is a manual wall holder with a hinged strike for drywall and masonry - the hold is engaged and released by hand, which suits a door that should only stand open when someone deliberately sets it. The Ives WS40 is an automatic wall holder with a heavy duty bumper pad, which catches the door on contact without anyone bending down. The WS40 is light duty, while the WS20 is heavy duty, so match the choice to how hard the door lands.

They are the same category of part and mount the same way, but they are not the same size or the same look. The Emtek 2255 is a 2-3/4 inch diameter brass wall bumper with a rubber tip, styled to match Emtek rosette trim. The Delaney concave wall bumper is 2-1/4 inch, so it presents a smaller rosette on the wall. If the goal is to match the plate diameter of bumpers already installed elsewhere in the building, that half inch is the deciding number, and the 2255 finish range covers oil rubbed bronze, flat black, flat black bronze, satin brass, and French antique.

Split the standard by door duty rather than forcing one part everywhere. The Emtek 2255 is a brass, American Classic style bumper meant for residential openings, so it suits unit entry and interior doors where appearance matters. For back of house, corridors, and mechanical rooms, the Ives WS11 and Ives WS33 are heavy duty wall stops with replaceable rubber bumpers rated for drywall or masonry. The ABH RM and RMS Series offer multiple length options, which matters where baseboard or trim pushes the strike point off the wall plane.

A wall bumper covers only the footprint of its own rosette, and the Emtek 2255 is 2-3/4 inch in diameter, so anything wider than that stays exposed. Where a removed stop leaves an opening that a new bumper will not conceal, the Delaney 2-1/8 inch hole plate metal cover is the part for it - it is a cover plate, not a stop, and it does nothing to arrest the door. If the door still needs stopping at that location, order the cover and a stop as two separate items.

The Emtek 2255 is a brass wall mount bumper supplied for residential openings, where the substrate is typically drywall with backing. The Ives WS11 and WS33 are the parts specified when the anchor has to go into either drywall or masonry, and the Ives WS20 wall holder covers the same two substrates. On a concrete or CMU corridor wall, that substrate range is the reason contractors specify the Ives stops over a residential brass bumper.

The 2255 is a single projection bumper with a 2-3/4 inch rosette, so where a long lever or a thick baseboard means the door hits before the bumper does, a variable length stop solves it. The ABH RM Series and the ABH RMS Series wall door stops are both offered with multiple length options, letting you pick a projection that reaches past the trim and takes the door before the lever contacts the wall. Measure from the finished wall surface to the point on the door that lands first, then select the length from that dimension.

Solid brass, both the material and the substrate. That matters on a bumper because a plated steel body will rust at the fastener once the finish is chipped, and a brass one will not. The styling is Emtek's American Classic look.

Not directly - they meet the door in different places. The Emtek 2255 mounts on the wall and takes the door face on a rubber tip. The Delaney 3 inch spring door stop mounts at the floor or base and flexes as the door swings into it, which means the door stops short of the wall entirely and the wall never needs an anchor. Choose the spring stop where the wall cannot be drilled or where the door edge, not the face, is what reaches the stopping point; choose the 2255 where the door face lands flat against a wall.