Emtek 92015 Heavy Duty Plain Bearing Hinges (Pair), 4-1/2" x 4-1/2" with Square Corners, Plated Steel

Yes. The Emtek 92015 plain bearing hinge is rated for doors up to 1-3/4 inches thick, which covers the standard exterior and solid-core interior door. The leaf size is 4-1/2 x 4-1/2 inches, so the door needs a mortise cut for a 4-1/2 inch leaf, not the 3-1/2 inch pocket found on most lightweight interior doors.

Square corners. That matters because the mortise already cut in your door and jamb has to match: a square-corner hinge will not seat in a pocket routed with a 5/8 inch or 1/4 inch radius without chiseling the corners out. If your existing pockets are rounded, look at a radius-corner hinge instead, such as the Delaney 4 x 4 exterior residential hinge with a 5/8 inch radius or the Orca Hardware 4 x 4 x 1/4 inch radius corner plain bearing hinge.

They ship as a pair, two hinges, with screws included. Most interior doors take three hinges and a heavy exterior door often takes four, so plan on ordering two pairs per opening if you want the third hinge covered. Nothing else is needed to hang the door on these.

Plain bearing is the right call for residential openings with normal traffic: no bearing races, just the knuckles riding on each other, and it runs quiet. Emtek rates the 92015 as a residential hinge. Where the door carries a closer, sees continuous traffic, or is heavy enough to sag, a bearing hinge is the better choice: the Don-Jo HWBB74545 heavy weight full mortise ball bearing hinge in the same 4-1/2 x 4-1/2 size, or the Orca Hardware 3535 Series 4-1/2 x 4-1/2 square corner ball bearing hinge.

Emtek lists the 92015 as a residential hinge, and it uses a plain bearing rather than a bearing race, so it is not the part for a high-cycle commercial opening or a door with a closer on it. For those, go to a commercial bearing hinge: the Ives 3CB1HW steel heavy weight concealed bearing full mortise hinge, the Hager BB1168 heavy duty full mortise ball bearing hinge with non-removable pin, or the Stanley FBB191 5-knuckle full mortise in the same 4-1/2 x 4-1/2 size.

No. The 92015 is a standard pin hinge, and on an outswing door the barrel sits outside where the pin can be driven out. For that opening you want a non-removable pin or security hinge: the Deltana CSB45N 4-1/2 x 4-1/2 square hinge with non-removable pin matches this size and corner style, and the Deltana DE44R5TA 4 x 4 security hinge is the radius-corner option.

The Emtek 92015 carries no wiring. To run power through the hinge to an electric strike, electrified lock, or exit device, you need a transfer hinge. The Command Access ETH-BB68 is a 5 knuckle heavy duty steel base energy transfer hinge, and the ETH-CB70 is a 3 knuckle standard weight version at a medium duty rating. If the opening also needs door position reporting back to the access control panel, the Command Access ETM-BB68 is an energy transfer monitor hinge with an integrated door position switch, and the ETM-CB70 does the same on a 3 knuckle steel base. The BEST CECB179-12C is a steel full mortise concealed bearing electrified hinge with a 12-wire quick connect for higher wire counts.

The Emtek 92015 is a 4-1/2 inch by 4-1/2 inch square corner plain bearing hinge sold as a pair. The Deltana CSB45N is also a 4-1/2 inch by 4-1/2 inch square hinge sold as a pair, so it drops into the same mortise and the same screw pattern; the CSB45N is built with a non-removable pin, which fixes the pin in place once the door is hung. The Orca Hardware COM3535 is another 4-1/2 inch by 4-1/2 inch square corner hinge, built as a ball bearing hinge rather than a plain bearing one. Both match the 92015 footprint, so the decision comes down to bearing type and pin style rather than door prep.

The Emtek 92015 is a plain bearing hinge listed for residential use. For an opening that cycles heavily, a bearing hinge in the same 4-1/2 inch by 4-1/2 inch size carries the load on bearings instead of bare knuckles: the Don-Jo HWBB74545 and HWBB84545 are heavy weight full mortise ball bearing hinges at 4-1/2 inch by 4-1/2 inch in satin chrome, and the Ives 3CB1HW is a steel heavy weight concealed bearing full mortise hinge with 3 knuckles. The Orca Hardware COM3535 is a 4-1/2 inch by 4-1/2 inch square corner ball bearing commercial hinge at a medium duty rating for openings between the two.

The Emtek 92015 has square corners, which need a square-routed mortise or a chiselled corner. For a factory radius prep, the Delaney RH45xx is a 4 inch by 4 inch bulk residential exterior hinge with a 5/8 inch radius, sold as a pair, and the Delaney RH35xx is the same 5/8 inch radius in a 3-1/2 inch by 3-1/2 inch interior size. For a 1/4 inch radius rather than 5/8 inch, the Orca Hardware COM4014 is a 4 inch by 4 inch plain bearing commercial hinge with a 1/4 inch radius corner. Measure the corner radius on the hinge you are pulling before ordering, since 1/4 inch and 5/8 inch preps are not interchangeable.

The Emtek 92015 is a standard plain bearing hinge pair. On an out-swinging exterior or storage door where the hinge knuckles are exposed, a security pin matters more than bearing type. The Deltana CSB45N is a 4-1/2 inch by 4-1/2 inch square hinge pair built with a non-removable pin, matching the 92015 size and corner. The Hager BB1168 is a non-removable pin full mortise ball bearing hinge at a heavy duty rating for a commercial opening. The Deltana DE44R5TA is a 4 inch by 4 inch security hinge in steel with a 5/8 inch radius corner, sold as a pair, for a prep with rounded corners.

The Emtek 92015 is a standard plain bearing hinge with no closing mechanism, so the door stays where you leave it. The Stanley Security 2060R is a full mortise spring hinge at 4.5 inch by 4.5 inch with a square corner on a ferrous steel base, rated heavy duty, which matches the 92015 size and corner style while pulling the door closed on its own. That makes it the direct swap for a garage-to-house door or any opening where the door has to latch every time without a surface closer.

The Emtek 92015 is a full mortise hinge, meaning both the door edge and the jamb are routed. Where the frame cannot be cut, the Hager 1129 is a half mortise plain bearing commercial hinge at 4-1/2 inch in standard weight steel, rated heavy duty, which mortises into the door and applies to the face of the frame. That suits a metal frame or an existing jamb you do not want to modify, and it keeps the same plain bearing action as the 92015.

Not handed. The 92015 is a full mortise butt hinge with a symmetrical pair of leaves, so the same hinge works on a left hand or right hand opening. You just flip it. Handing only becomes an ordering decision on hinges with a fixed feature on one leaf, like electrified or non-removable-pin models.

Eleven finishes, so you can match the hinge to the lockset already on the opening: Polished Brass Lifetime (US3), 606 Satin Brass, French Antique (US7), Medium Bronze (MB), Tumbled White Bronze (TWB), 613 Satin Bronze Oil-Rubbed, Polished Nickel (US14), 619 Satin Nickel, Pewter (US15A), Flat Black (US19), and 625 Bright Chrome. Order by the model plus finish code, for example 92015MB for Medium Bronze or 92015TWB for Tumbled White Bronze.

Steel with a plated finish. The 92015 is built on a steel base and the finish is applied over it, which is why the finish list runs to brass, bronze, nickel and black tones without the part being solid brass. For a project spec that calls out a non-ferrous hinge, steel base will not satisfy it.

Leaf gauge runs 0.118 to 0.126 inches. That is the number to check against the mortise depth already cut in your jamb: a heavier gauge hinge dropped into a shallow pocket leaves the leaf proud and the door will not close square. It also tells you the hinge is a heavy duty plain bearing rather than a thin builder-grade stamping.

The 92015 itself is the 4-1/2 x 4-1/2 size. Emtek's heavy duty plain bearing line also covers 3-1/2 x 3-1/2 and 4 x 4 sizes for lighter interior doors, all of them square corner. Measure the leaf on the hinge you are pulling off before ordering, since a 3-1/2 inch pocket will not take a 4-1/2 inch leaf without recutting the jamb.

If the existing hinges are 4-1/2 x 4-1/2 with square corners and the doors are 1-3/4 inches or less, the 92015 drops into the same mortise. What will not match automatically is the finish tone across brands, so if you are replacing hinges door by door across a house or a building, pick one of the eleven Emtek finishes and run it through the whole set rather than matching to whatever is on each opening now.

They share a bearing type and corner style but not the pack or the size. The Ives 1010RP is a steel plain bearing residential hinge with square corners sold as a set of three, at a medium duty rating. The Emtek 92015 is a plated steel plain bearing hinge with square corners at 4-1/2 inch by 4-1/2 inch, sold in pairs with screws included. If you are hanging a door that takes three hinges, the 1010RP covers the opening in one pack; if you are matching an existing 4-1/2 inch square mortise, check the 1010RP size against the prep before you order.

Both are plain in appearance from the edge of the door, but the bearing sits differently. The Emtek 92015 uses a plain bearing, where the knuckles ride directly on each other. The Hager 920 is a full mortise concealed plain bearing hinge with 2 knuckle steel construction at a medium duty rating, so the bearing is hidden inside the knuckle rather than exposed as a visible bearing race. The Ives 3CB1 is a 3 knuckle concealed bearing full mortise hinge, also medium duty. Concealed bearing hinges keep the clean barrel line while adding a bearing surface, which matters where the door is heavy or the swing is frequent.

The Emtek 92015 is 4-1/2 inch by 4-1/2 inch, a square leaf. On a thicker door or where the trim requires the door to clear further off the jamb, a wider leaf gives the extra throw. The Don-Jo HWBB75045 is a heavy weight full mortise ball bearing hinge at 5 inch by 4-1/2 inch in steel with a satin chrome finish, and the HWBB85045 is the same 5 inch by 4-1/2 inch size in brass with satin chrome. Both are rated heavy duty. Note that the 5 inch height also changes the mortise, so this is not a leaf-width-only swap.

No, and these are worth ruling out early because they look adjacent in a hinge search. The BEST BB855 is a heavy-duty steel double weight concealed ball bearing prison hinge in the detention hardware series, and the Stanley BB855 is a double weight prison hinge furnished with no holes and not swaged at 5 inch by 6 inch, which means it arrives undrilled and needs shop prep rather than dropping into a residential mortise. The Hager 990 STEEL is a full surface prison hinge at 3 inch by 4 inch with a welded tip, mounted to the face of the door rather than mortised in. The BEST DAP-3 is a heavy duty double acting pivot for commercial interior doors, a pivot rather than a hinge, so it uses top and bottom door prep instead of edge mortises.

The Emtek 92015 is a plated steel hinge in an American Classic theme with square corners. If the barrel itself is part of the look, the McKinney SQ3331 is a square barrel 2-knuckle decorative hinge at 4-1/2 inch by 4-1/2 inch, standard duty, which trades the rounded five-knuckle barrel for a squared profile that reads with modern square rosettes and square-edge trim. Both are 4-1/2 inch by 4-1/2 inch, so the door and jamb prep is the same and the choice is purely the visible barrel.

The Emtek 92015 covers the 4-1/2 inch by 4-1/2 inch square corner openings. Where the same building has 4 inch preps, the Orca Hardware COM4040 is a 4 inch by 4 inch square corner plain bearing commercial hinge at a medium duty rating, holding the same bearing type and corner style one size down. The Delaney CH401X is a 4 inch by 4 inch commercial ball bearing hinge with a square corner if you want a bearing hinge on the higher traffic doors in the same square prep. Pairing by corner style first keeps one mortise profile across the fleet even where hinge heights differ.

The Emtek 92015 is built on a steel substrate with a plated finish. In a coastal, pool, or wash-down opening where a steel base is the wrong choice, the McKinney T2314 is a non-ferrous hinge, standard weight, 5 knuckle, at a medium duty rating. Non-ferrous base material resists the rust that attacks a plated steel hinge once the plating is scratched at the screw heads or the knuckle. Confirm the size against your existing mortise, since the base material is the change being made here, not the prep.

If you want the conventional five-knuckle barrel in the same 4.5 inch by 4.5 inch size, the Stanley Security FBB191 is a 5-knuckle full mortise standard weight hinge at 4.5 inch by 4.5 inch, rated heavy duty. In the same family of standard weight five-knuckle full mortise hinges, the McKinney MP79 MacPro is a 5-knuckle full mortise hinge at standard weight, and the MPB79 MacPro is a 5-knuckle standard weight hinge as well. All three keep the full mortise prep the Emtek 92015 uses, so the door and jamb routing carries over.

The Emtek 92015 is a plain hinge with no reinforcement or wiring. Where the frame or door corner needs the load carried differently, the BEST CB1969R is a concealed bearing heavy weight pivot-reinforced hinge, rated heavy duty. Where an electrified opening needs the wire hidden and the handing fixed at order, the Stanley CECB1900R54L is a three knuckle concealed bearing concealed conductor architectural hinge in steel full mortise, standard weight, 4-1/2 inch by 4-1/2 inch, square corner, left-handed, with 4 wires. That last one matches the 92015 size and corner but is handed, so confirm the door swing before ordering.

The corner treatment is the difference that decides the fit. The Emtek 92015 is a 4-1/2 inch by 4-1/2 inch hinge with square corners on both leaves. The Delaney RH40xx is a 4 inch by 4 inch residential hinge for Castlegate with a 5/8 inch radius on one leaf and a square corner on the other, sold as a pair, which suits a door with a radius-routed edge hung in a square-cut jamb. Check which leaf is which before you set the door, because reversing them leaves a gap at the mortise corner.

The Emtek 92015 at 4-1/2 inch by 4-1/2 inch is sized for a passage or entry door. For a light closet, cabinet, or narrow-stile door, the Deltana DSB3 is a 3 inch by 3 inch square hinge sold as a pair, keeping the square corner profile at a smaller leaf. If the door falls between the two, the Deltana DSB35 is a 3-1/2 inch by 3-1/2 inch square residential hinge, also sold as a pair. Match the leaf height to the existing mortise rather than to the door width.