Emtek Westridge Cabinet Pull, Schaub Collection

The Westridge pull is offered in 3-1/2, 4, 5, 6, 8, 10, and 12 inch center-to-center. Measure hole to hole on your existing pull, center of one screw to center of the other, and match that number. The longer 8, 10, and 12 inch sizes are what people put on wide drawer banks and appliance panels; the 3-1/2 and 4 inch sizes suit standard base cabinet drawers and doors.

Emtek specifies the Westridge as residential hardware. For single-family, condo, and multi-family unit interiors it is on spec. For a heavy-traffic commercial casework job, an institutional or MRO buyer is usually better served by something built for that duty, such as the Schaub 79-8 Steamworks 8 inch appliance pull or the Orca Hardware CK-12001 T-pull bar in steel.

The Deltana SBP35 Modern Square Bar Pull is a solid brass bar pull at 3-1/2 inch center to center, part of Deltana's SBP Series. The Westridge pull is also brass and includes 3-1/2 inch among its center-to-center sizes, so the two land on the same drilling. The difference is form: the SBP35 is a square-profile modern bar, while the Westridge is styled as an American Classic. If the cabinet run is already drilled at 3-1/2 inch, either drops into the existing holes.

The Omnia 1968/102 is a forged solid brass modern cabinet pull with 4 inch center-to-center spacing. The Emtek Westridge also comes in 4 inch center to center in brass, but is styled American Classic. Same hole spacing, different look, so a kitchen already bored at 4 inch can take either without redrilling.

No. The Schaub Sabre 10010, 10011 and 10012 are edge pulls, a different function from a face-mounted cabinet pull. An edge pull mounts on the edge or lip of a door or drawer front rather than through two holes in the face, so it does not use the same boring as the Westridge and does not present a grip on the door face. The Sabre edge pulls do run 3 inch, 4 inch and 5 inch center to center, matching sizes the Westridge offers, but the mounting is not interchangeable.

Appliance fronts take an appliance pull, which is built for the weight and the repeated hard pull a fridge or range door sees. The Schaub 79-8 Steamworks 8 inch cabinet pull is designated an appliance pull. The Emtek Westridge is a cabinet pull and also reaches 8 inch center to center, along with 10 inch and 12 inch, so if the run needs to look continuous across cabinets and appliance, matching those longer sizes is the way to line the two up.

They cover overlapping drillings but different sizes. Trimco 553 Series drawer pulls are 3 inch center to center, a spacing the Westridge does not offer. Trimco 562 Series comes in 3-1/2 inch, 4 inch and 96mm, and the first two of those match Westridge sizes. For a fleet of units already drilled at 3 inch, the 553 fits the existing holes; at 3-1/2 or 4 inch, either the 562 or the Westridge lands on the same centers.

Mounting screws come in the box with the pull, so nothing extra is needed for a standard install. If your drawer fronts are thicker than usual (a slab front with an applied panel, for example), plan on sourcing longer machine screws in the same 8-32 thread, since the supplied screws are cut for typical front thickness.

Six finishes: Flat Black (US19), Oil Rubbed Bronze (US10B), Polished Chrome (US26), Polished Nickel (US14), Satin Brass (US4), and Satin Nickel (US15). Those US numbers are the standard finish codes, so if your door hardware is already specified as US15 satin nickel or US10B oil rubbed bronze, ordering the same code keeps the kitchen and the doors reading as one set. Oil rubbed bronze is a living finish and will shift with handling over time.

Pulls like the Westridge give you a two-screw mount and a full-hand grip, which is what you want on drawers, on anything heavy, and where ADA-style ease of grasp matters. Knobs use a single screw and suit small upper doors. A common approach is knobs on the upper doors and pulls on the drawers. If you want the knob for part of the run, the Orca Hardware Bachelor Collection round cabinet knob at 1-1/4 inch diameter or the Blackcomb Collection square knob at 25mm are options.

On a panel-ready appliance with a wood front drilled to match, the 10 and 12 inch center-to-center Westridge sizes are the ones that carry that scale. On a factory appliance handle with a fixed bracket spacing, it will not adapt. For a purpose-built appliance pull, the Schaub 79-8 Steamworks 8 inch pull is catalogued for that function.

No. The Westridge is a surface-mounted pull that stands proud of the front, so it will foul anything that slides past a jamb or another panel. For those openings you want an edge pull instead, such as the Schaub Sabre edge pull, offered at 3, 4, and 5 inch center-to-center.

Projection is the number to check when hands or gloves need room behind the grip. The Omnia 1970 forged solid brass cabinet pull carries a 1-1/4 inch projection, and both the Omnia 1969 and Omnia 1971 carry 1-3/16 inch. All three are forged solid brass modern pulls, so the choice among them comes down to that projection figure and the pull's outline.

The Orca Hardware CK-12001 T-Pull Bar is steel with a 2 inch bar width, finished satin nickel. The Emtek Westridge is brass and offered in a satin nickel finish as well, so the two can be matched visually across a job even though the base material differs. Emtek lists the Westridge as residential, which is worth weighing against the duty a shop or back-of-house cabinet actually sees.

The Emtek Westridge itself is the one that runs long, with center-to-center sizes up to 10 inch and 12 inch in brass. Among the peers, the Schaub 79-8 Steamworks reaches 8 inch and the Omnia 1968/102 is a 4 inch pull, so for tall pantry or full-height doors the Westridge's 10 and 12 inch sizes are what carry the proportion, in any of six finishes from flat black through polished nickel.

Yes, and it is the usual way it gets specified. All seven center-to-center sizes from 3-1/2 up to 12 inches come in the same six finishes, so a property manager or remodeler can run 3-1/2 or 4 inch on the doors, 5 or 6 inch on the standard drawers, and 10 or 12 inch on the wide drawer bank, all in one finish code. Ordering by the same US number across the run is what keeps the plating batch-consistent.