Mulberry Die-Cast Aluminum Com...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$8.12
Image coming soon

Mulberry Die-Cast Aluminum Combination Conduit Body

(No reviews yet) Write a Review

Model: 14811

In Stock (leaves warehouse same day if ordered before 3pm ET)

$8.12
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like

Mulberry Die-Cast Aluminum Combination Conduit Body

The Mulberry Combination Conduit Body is a die-cast aluminum fitting built for electrical conduit systems that require a rugged, corrosion-resistant access point for pulling, splicing, or redirecting conductors. This family is available in C, LB, LL, LR, and T body configurations across trade sizes from 1/2" to 2", giving installers a combination body suited to nearly any conduit routing or direction-change requirement. Each body ships complete with a matching die-cast cover and gasket, ready to close out once wiring work is finished. Built for ongoing commercial and industrial electrical work, the die-cast aluminum housing withstands repeated handling and jobsite exposure.

Key Features

  • Multiple Body Configurations: Offered in C, LB, LL, LR, and T combination body types, giving installers a low-profile access point matched to the specific routing or direction-change need at hand.
  • Trade Size Range: Available in trade sizes from 1/2" to 2", covering the sizing needs of most commercial and industrial conduit runs.
  • Die-Cast Aluminum Construction: Manufactured from die-cast aluminum, each body offers a rugged, corrosion-resistant housing built to withstand repeated handling and environmental exposure typical of conduit installations.
  • Combination Configuration: As combination bodies, these fittings accommodate flexible conduit routing, giving installers a single access point that can serve multiple wiring paths at a junction or turn.
  • Included Cover: A matching die-cast cover ships with each body, allowing the fitting to be fully closed out as soon as conductor work inside the body is complete.
  • Included Gasket: A gasket is provided between the cover and body to help create a tighter seal at the joint, reducing the chance of dust or moisture intrusion into the conduit body.
  • Ready-to-Install Assembly: Because the cover and gasket ship with the body, electricians do not need to source matching hardware separately, simplifying material lists and speeding up rough-in.

Technical Specifications

  • Refer to manufacturer documentation for complete technical specifications.

Typical Applications

  • Commercial and Industrial Electrical Installations
  • Conduit and Raceway Systems
  • Conductor Pulling and Splicing Points
  • Renovation and New Construction Projects

Why Mulberry?

Mulberry manufactures this combination conduit body family from die-cast aluminum to give electrical contractors a durable, corrosion-resistant fitting that holds up to daily jobsite use. Shipping complete with a matching cover and gasket across every C, LB, LL, LR, and T configuration, these bodies provide a ready-to-use access point for conduit runs, helping keep splice and pull locations clean, secure, and organized. For contractors standardizing on dependable conduit body hardware, Mulberry's combination fittings offer a straightforward, complete solution for routing and access needs across commercial and industrial conduit systems.

Manufacturer Resources

Product Specs

Product Material:
Die-Cast Aluminum
Configuration:
Type LR Combination
Product Type:
Conduit Body
Department:
Electrical
Product Group:
Wiring Devices
Product Size:
1/2" - 2"

Mulberry 14811 – Frequently Asked Questions

1) What trade sizes do Mulberry die-cast aluminum conduit bodies come in?
The family runs 1/2 inch to 2 inch trade size, but not every body type covers the full range. LB is the one that goes all the way: 1/2, 3/4, 1, 1-1/4, 1-1/2, and 2 inch. The LL, LR, C, and T bodies are offered in 1/2, 3/4, and 1 inch only. So if you are turning a 1-1/4 inch or larger run, an LB is the body available in that size.
2) Can I use an aluminum conduit body on a run of rigid steel or EMT conduit?
Aluminum in direct contact with steel raceway in a wet location invites galvanic corrosion, so the usual practice is to match the body material to the raceway: aluminum bodies on aluminum rigid conduit, and a coated or malleable iron body where the run is rigid steel in a corrosive or wet spot. Indoors and dry, the die-cast aluminum Mulberry body is common on threaded rigid runs. For steel runs where you want a coated fitting instead, the ABB Form 7 PVC-coated LB is an iron-bodied alternative.
3) What is the difference between a Mulberry die-cast aluminum LB conduit body and an ABB Form 7 PVC-coated LB?
Both are LB-configuration conduit bodies, so they serve the same 90-degree back-access pull point in a conduit run. The material is what separates them: the Mulberry LB bodies are die-cast aluminum, while the ABB Form 7 LB is iron with a PVC coating. The Mulberry family also spans C, LB, LL, LR and T configurations in trade sizes from 1/2 inch to 2 inch, so a contractor standardizing on one line can pull every direction change from the same family. Aluminum is the common choice for general commercial and industrial dry and damp conduit work; a PVC-coated iron body is the specification when a corrosive or wash-down environment is called out on the drawing.
4) Can a PVC-coated iron LB be swapped for an aluminum LB on the same conduit run?
Mechanically the LB configuration is the same fitting geometry either way, so an ABB Form 7 PVC-coated iron LB and a Mulberry die-cast aluminum LB of the same trade size both land a back-access pull point at a 90-degree turn. The substitution to watch is the coating system: a PVC-coated body is normally specified as part of a coated raceway system, where the conduit, couplings and body are coated together and the joints are sealed at install. Dropping an uncoated aluminum body into that run breaks the continuity of the coating. Going the other direction, on a standard uncoated run, the Mulberry aluminum bodies cover 1/2 inch through 2 inch and ship with a matching die-cast cover and gasket, so no separate cover hardware is needed.
5) I need an LL or LR body, not an LB - what are my options?
The ABB Form 7 comparable is an LB body only, which gives back access at a turn. If the run needs the opening on the left or right side instead, the Mulberry die-cast aluminum family covers LL and LR in 1/2 inch, 3/4 inch and 1 inch trade sizes, along with C bodies for a straight pull-through and T bodies for a three-way junction in those same sizes. That makes the Mulberry family the one to pull from when a single job needs several body types matched in the same material and cover style.
6) Do I have to buy the cover and gasket separately for a Mulberry conduit body?
No. Each Mulberry combination body ships with a matching die-cast cover and a gasket already, so the fitting closes out as soon as the conductors are in. Nothing extra goes on the material list for the cover side of it.
7) Is a die-cast aluminum conduit body OK outdoors or in a damp area?
The housing is die-cast aluminum, which is corrosion resistant and holds up to jobsite exposure, and the gasket between cover and body tightens the joint against dust and moisture. That covers ordinary exterior and damp conduit work. Where the environment is chemically aggressive, a coated body is the better call: ZenSupply also carries the ABB Form 7 PVC-coated LB body, which is iron with a PVC coating rather than bare aluminum.
8) Can I splice wires inside a Mulberry conduit body, or is it only for pulling?
Both. The die-cast aluminum combination bodies are built as access points for pulling, splicing, or redirecting conductors, which is why the cover and gasket come with them. Keep in mind that whether a given body has room for splices depends on its listed conductor volume for the wire you are running, so size the body to the fill, not just to the trade size of the conduit.
9) Which conduit body should I use above 1 inch trade size?
In the Mulberry die-cast aluminum family, the LB configuration is the one that carries past 1 inch: LB bodies run 1/2 inch, 3/4 inch, 1 inch, 1-1/4 inch, 1-1/2 inch and 2 inch, while the C, LL, LR and T configurations top out at 1 inch. So a 1-1/4 inch or larger run calls for the LB body, part numbers 14804, 14805 and 14806 respectively. The ABB Form 7 comparable is likewise an LB body, which is the coated-iron route for the same back-access turn.
10) Does a conduit body need a cover ordered separately like some coated fittings?
Not with the Mulberry die-cast aluminum bodies - each one ships complete with a matching die-cast cover and a gasket between the cover and body, so the fitting can be closed out as soon as the conductors are pulled or spliced. That applies across every C, LB, LL, LR and T configuration in the family. Coated systems such as the ABB Form 7 PVC-coated iron LB are specified as part of a coated raceway assembly, where cover and sealing details follow that system's requirements, so check the coated-system documentation before assuming the same parts list.
11) Can I standardize one brand of conduit body across a whole building and get every configuration I need?
For runs at 1 inch and below, yes, the Mulberry die-cast aluminum family covers all five configurations (C, LB, LL, LR, T) in matching aluminum with the same cover and gasket arrangement, so a facility or contractor can carry one brand across pull points, turns, and branches. Above 1 inch, the family narrows to LB through 2 inch, so larger runs will need their direction changes planned as LB turns.
How fast can I get the Mulberry 14811 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Mulberry 14811 come with a warranty?
Absolutely. The Mulberry 14811 is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Mulberry 14811?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Mulberry 14811 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!