nVent CADDY 304B2 Spring Steel...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$1.56
nVent CADDY 304B2 Spring Steel Press-On Nail Plate, 3-1/8-Inch x 1-1/2-Inch

nVent CADDY 304B2 Spring Steel Press-On Nail Plate, 3-1/8-Inch x 1-1/2-Inch

(No reviews yet) Write a Review

Model: 304B2

In Stock (leaves warehouse same day if ordered before 3pm ET)

$1.56
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like

nVent CADDY 304B2 Spring Steel Press-On Nail Plate, 3-1/8-Inch x 1-1/2-Inch

The nVent CADDY Spring Steel Press-On Nail Plate is a stud protection plate engineered to shield electrical wiring, low-voltage cable, and piping from accidental nail and screw penetration during drywall installation and finish work. Measuring 3-1/8-Inch x 1-1/2-Inch, this plate is stamped from durable spring steel and installs with a simple press-on method directly over the face of a wood or metal stud, joist, or framing member, requiring no additional fasteners, adhesives, or specialty tools. Electricians and general contractors rely on plates like this one to add a dependable layer of protection wherever conductors, cable, or tubing pass through drilled or notched framing near a finished wall or ceiling surface. Because it seats securely by hand, it fits easily into a standard rough-in workflow without slowing down the crew.

Key Features

  • Compact Footprint: Sized at 3-1/8-Inch x 1-1/2-Inch, proportioned to cover the typical width of a drilled or notched framing member without unnecessary bulk.
  • Spring Steel Construction: Stamped from spring steel for a rigid, puncture-resistant barrier that stands up to job-site handling.
  • Press-On Installation: Snaps directly onto the framing member by hand, so crews can protect a run without extra fasteners or tools.
  • Purpose-Built Stud Protection: Designed specifically to guard wiring, cable, and piping routed through studs and joists from accidental fastener strikes.
  • Low-Profile Fit: Sits flush against the framing face so it does not interfere with drywall or finish surfaces once installed.
  • Job-Site Durability: Spring steel resists bending and deformation during transport and handling, keeping the plate ready to perform when it is installed.

Technical Specifications

  • Refer to manufacturer documentation for complete technical specifications.

Typical Applications

  • Wood and Metal Stud Framing Protection
  • Electrical Rough-In and Cable Routing
  • Protection of NM Cable and Low-Voltage Wiring Through Studs and Joists
  • Residential and Commercial Construction
  • Renovation and Remodel Wiring Projects
  • Plumbing and Conduit Penetrations Through Framing Members

Why nVent CADDY?

nVent CADDY builds this nail plate from spring steel so it holds up to the punctures and impacts a stud protection plate is meant to stop, giving electricians and contractors a dependable barrier for wiring and piping run through framing. Its press-on design lets crews install protection quickly by hand during rough-in, without adding fasteners, adhesives, or extra steps to the job. For professionals who need a simple, durable way to keep conductors safe from drywall screws and nails, this plate offers a straightforward, code-conscious solution built for repeated job-site use.

Manufacturer Resources

nVent CADDY Full Catalog

Product Specs

list_batch:
CDY-20260915
Product Type:
Nail Plate
Connection Type:
Press-On
Department:
Electrical
Product Group:
Hangers, Supports & Fasteners
Product Subgroup:
Hangers, Straps & Supports
Product Material:
Spring Steel

nVent CADDY 304B2 – Frequently Asked Questions

1) Will the nVent CADDY 304B2 nail plate cover a standard 2x4 stud face?
The 304B2 plate measures 3-1/8 x 1-1/2 inches, which covers the 1-1/2 inch face width of a nominal 2x4 or 2x6 stud and gives you about 3-1/8 inches of length along the framing member. That is enough to shield a drilled bore or a notch where cable or tubing crosses the stud face. If your bore is larger than the plate footprint, you need more than one plate or a larger protection plate.
2) Do I need nails or screws to install the CADDY 304B2 stud protection plate?
No fasteners at all. The 304B2 is a press-on plate: it snaps onto the edge of the framing member by hand, and the spring steel holds it there. No nails, screws, adhesive, or special tool is part of the install, which is why crews can drop them in during rough-in without breaking stride.
3) Can the 304B2 press-on nail plate be used on metal studs, or wood only?
Both. The 304B2 presses onto wood or metal studs, joists, and other framing members. The spring steel body grips the edge of the member either way, so the same plate works on a residential wood-framed wall and a commercial light-gauge metal stud partition.
4) Is this nail plate only for electrical wire, or can I use it over plumbing runs too?
It is not limited to conductors. The 304B2 is used over NM cable, low-voltage cable, and piping or tubing routed through drilled or notched framing. Plumbers and HVAC trades use the same plate where a line crosses a stud close to the drywall face.
5) Will the CADDY 304B2 plate cause a bulge under the drywall?
No. The plate is low profile and seats flush against the face of the framing member, so drywall lays flat over it. That matters most where you have several plates in a row on one stud bay and any proud edge would telegraph through the finish.
6) What is the exact part number to order for the 3-1/8 by 1-1/2 inch CADDY press-on nail plate?
Order nVent CADDY part 304B2. That is the single model on the 3-1/8 x 1-1/2 inch spring steel press-on nail plate, so there is no finish, size, or handing choice to specify with it.
7) Why spring steel instead of a plain stamped steel nail plate?
Two reasons. Spring steel gives a rigid, puncture-resistant barrier against a drywall screw or nail strike, and it is what lets the plate grip by press-on fit rather than needing prongs driven into the wood. It also resists bending in a tool bag or bucket, so plates arrive at the wall straight and still snap on tight.
8) Can I use the 304B2 nail plate on a remodel where the wall is already partly finished?
Yes, as long as you can still reach the edge of the framing member to press the plate on. Renovation and remodel wiring is one of its normal uses, and because it needs no fasteners or tools you can protect a fished run in an open bay and close it up immediately.
How fast can I get the nVent CADDY 304B2 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the nVent CADDY 304B2 come with a warranty?
Absolutely. The nVent CADDY 304B2 is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the nVent CADDY 304B2?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the nVent CADDY 304B2 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!