Pamex DD02-61 1-3/4" Diameter Low Profile Dome Stop

The DD02-61 dome stop projects 15/16 inch from the mounting surface. That is the stopping distance you get, so measure from your baseboard or floor face to where the door edge or knob would land. If your knob overhangs more than about an inch, a low dome like this will let the trim hit before the stop does, and you want a taller gooseneck instead, like the Orca Hardware 22HD Series or the Emtek 2253 goose style stop.

Not usually. At 15/16 inch of projection, a low dome sits close to the floor, and carpet plus pad eats into that height before the door ever reaches it. Over carpet, a taller gooseneck that mounts to the baseboard, like the Orca Hardware 22HD Series or the Emtek 2253, catches the door above the pile. Save the low dome for hard flooring, or for wall mount behind the knob.

The DD02-61 is a brass, residential-duty dome stop. For openings that see commercial traffic, the Ives FS13 and FS17 brass floor dome stops are both rated heavy duty and keep the same low dome shape - the FS13 carries a replaceable rubber bumper, so the wear part can be renewed without pulling the base off the floor. The Ives FS18S / FS18L security floor stop is also heavy duty and is the one to specify where the stop itself needs to resist tampering.

The Orca Hardware 23LP Series dome floor stop is the closest match in form and function - it is a low rise dome floor stop with a gray tip, functioning as a door stop the same way the DD02-61 does. The Delaney Dome Door Stop is another dome-profile floor stop in the same family. All three sit low to the floor and take the door edge on a domed body rather than reaching up to a gooseneck arm.

A dome stop is a stop only; it arrests the door swing and releases it. For hold-open, the Ives FS40 / FS41 / FS42 / FS43 automatic floor stop and holder is built for it, with adjustable door-to-floor clearance. The Orca Hardware 22HD Series gooseneck floor stop is also catalogued as a door holder and fits doors 1-3/8 inch or 1-3/4 inch thick. The SOSS MDH is a magnetic door holder and stop measuring 3-5/16 inch by 1-3/4 inch, which catches and retains the door magnetically instead of mechanically.

A 15/16 inch projection is a low profile and it needs the door bottom close to the floor to make contact. Where the undercut is deeper, a gooseneck reaches up to meet the door: the Delaney Gooseneck Floor Door Stop, the Emtek 2253 Goose Style Door Stop, and the Orca Hardware 22HD Series gooseneck floor stop with black tip all use the raised arm profile. The Ives FS40 / FS41 / FS42 / FS43 goes further and offers adjustable door-to-floor clearance so the height is set at install rather than fixed.

Five finishes: 605 bright brass, 613 oil rubbed bronze, 619 satin nickel, 622 matte black, and 625 polished chrome. Those are standard BHMA finish numbers, so you can order the stop to the same number as the levers and hinges already on the opening and get a match across the fleet rather than eyeballing it.

No handing. The DD02-61 is a symmetrical dome on a round 1-3/4 inch base, so one part number covers every opening regardless of swing direction. For a property manager buying in quantity, that means one finish decision and one SKU across the whole building rather than tracking left and right.

The Orca Hardware 23LP Series is the direct counterpart, a low rise dome floor stop with a gray tip. The Emtek 2251 half dome door stop is the same silhouette in Emtek's line, and the Delaney Dome Door Stop covers it as well. All three keep the low dome format rather than the taller gooseneck.

They are not the same part even though both mount to the floor. The DD02-61 is a 1-3/4 inch diameter dome stop with a 15/16 inch projection that takes the door edge on the dome itself. The Deltana universal floor bumpers are a family of solid brass bumpers sized by cap: the UFB4505 round at 1-1/2 inch, the UFBP4505 with a pattern cap at 1-5/8 inch, the UFBS138 square at 1-3/8 inch, and the UFBD3505 decorative round at 3-1/2 inch. If you are matching an existing 1-3/4 inch round footprint, the bumper diameters will read differently on the floor.

The DD02-61 base is 1-3/4 inch in diameter and 1/8 inch thick, which keeps it visually quiet. If the design calls for a stop that reads as a deliberate floor detail, the Deltana UFBD3505 is a decorative round solid brass floor bumper at 3-1/2 inch, roughly double the diameter. The Deltana UFBP4505 at 1-5/8 inch adds a pattern cap instead of extra size. The SOSS MDH runs 3-5/16 inch by 1-3/4 inch and is the largest rectangular footprint in the group.

On a stop that gets struck daily, the rubber is the part that wears. The Ives FS13 is a heavy duty brass floor dome stop specified with a replaceable rubber bumper, so the tip is renewed in place. The Ives FS17 is also a heavy duty brass floor dome stop with a rubber bumper. Among the lighter dome and gooseneck options, the Orca 23LP Series carries a gray tip and the Orca 22HD Series a black tip, which is worth knowing when you are matching tip color across a set of doors.

They are close cousins rather than the same part. The DD02-61 is a low profile dome stop with a 1-3/4 inch base and a 15/16 inch projection, offered in matte black, polished chrome, oil rubbed bronze, bright brass and satin nickel. The Emtek 2251 is a half dome door stop - the same domed floor-mounted idea in Emtek's trim program. Emtek also runs the 2254 floor door bumper at 1-3/8 inch by 1-1/4 inch and the 2257 cylindrical floor bumper at 1-1/2 inch, both of which are bumper cylinders rather than domes.

The DD02-61 is a surface mount dome stop, which means the base sits on top of the finished floor and is anchored through it. Where abuse is the concern, the Ives FS18S / FS18L security floor stop is the heavy duty option built for openings that need the stop to resist interference. The Ives FS13, also heavy duty, takes a replaceable rubber bumper so the consumable can be swapped rather than replacing the whole stop unit by unit across a fleet of doors.

The DD02-61 is a surface mount floor stop and needs an anchor into the floor. Where that is not an option - stone, radiant slab, or a finish the owner will not let you penetrate - the SOSS MDH magnetic door holder and stop, at 3-5/16 inch by 1-3/4 inch and heavy duty, changes the geometry by catching the door magnetically. The Ives FS40 / FS41 / FS42 / FS43 automatic floor stop and holder is the other direction, mounting to the door itself with adjustable clearance down to the floor.

Brass. That is the body substrate under whatever finish you order, which is why the plated finishes hold up on a part that gets kicked and cleaned around. Solid brass alternatives in the same floor-bumper format include the Deltana UFB4505 at 1-1/2 inch and the Deltana UFBS138 square bumper at 1-3/8 inch.

The DD02-61 is built with a brass substrate. Among the peers, Deltana states solid brass construction across the universal floor bumper family - the UFB4505 round 1-1/2 inch, the UFBP4505 pattern cap 1-5/8 inch, the UFBS138 square 1-3/8 inch, and the UFBD3505 decorative 3-1/2 inch. The Ives FS13 and FS17 are brass floor dome stops in a heavy duty build. That matters where the stop lives in a wet or coastal environment and the base metal drives how it holds up.

The DD02-61 base is a 1-3/4 inch round dome. The Deltana UFBS138 is a square universal floor door bumper at 1-3/8 inch in solid brass, and it is the square-profile option in the group. Everything else nearby is round: the Deltana UFB4505 at 1-1/2 inch, the UFBP4505 pattern cap at 1-5/8 inch, and the Emtek 2257 cylindrical floor bumper at 1-1/2 inch.