Schaub 254 3" Center to Center Siena Cup Pull

Yes. The Siena 254 cup pull is drilled 3 inches center to center, which is the most common drawer pull spacing in North American cabinetry, so it drops onto existing 3 inch holes with no new boring. Mounting uses 8/32 thread screws, 1 inch long as supplied.

The 254 ships with 8/32 thread screws 1 inch long. On a standard 3/4 inch drawer front that leaves enough thread to seat the pull. If your drawer fronts are thicker, say a 3/4 inch box front with an applied face, you will need longer 8/32 screws. Machine-screw size is standard 8/32, so replacement lengths are easy to source.

Cup pulls are a drawer part. The 254 is grabbed from below the lip, which only works when the pull moves toward you, so it does nothing useful on a swinging door. Pair it with knobs or a bar pull on the doors. ZenSupply carries the Orca Hardware Bachelor Collection 1-1/4 inch round cabinet knob and the round ring version in the same collection for that side of the job.

Same 3 inch drilling, different look: the Trimco 553 Series drawer pull is a 3 inch center to center pull, so it lands on the same holes as the Schaub 254 without redrilling. The Trimco 562 Series runs 3-1/2 inch, 4 inch and 96mm centers, which means it will not reuse a 3 inch drilling.

The Trimco 553 Series drawer pull is built to 3 inch center to center, the same spacing the Schaub 254 Siena cup pull uses, so it drops onto drawer fronts already bored for the 254 without new holes. The difference is form: the 254 is a cup pull in a rustic style, offered in Ancient Bronze and Vibra Nickel, while the 553 is a drawer pull in the Trimco 553 Series. On a refresh where the boring stays and the look changes, that is the straight spacing-for-spacing swap.

The Schaub 254 Siena cup pull is a fixed 3 inch center to center, so wider boring needs a different part. The Trimco 562 Series drawer pull is made in 3-1/2 inch, 4 inch, and 96mm center to center, and the Deltana SBP35 is a 3-1/2 inch square bar pull in solid brass. For 4 inch spacing the Omnia 1968/102 is a forged solid brass cabinet pull at 4 inch center to center. Measure the existing hole spacing before ordering, since none of those interchange with the 254 boring.

Projection is 1 inch off the face. That matters in a galley kitchen or a tight hallway of built-ins where a hip catches a pull, and it matters for cup pulls in particular because your fingers go under the lip rather than around a bar. Overall size of the pull is 1-3/4 inches.

A cup pull like the Schaub 254 is grabbed from underneath, so it suits drawers and never doors, and it reads traditional or rustic. A bar pull works on both drawers and doors and is easier to grip with a full hand or a gloved one. If you want the bar format instead, ZenSupply carries the Emtek Bar Cabinet Pull and the Deltana SBP35 square bar pull in solid brass. Mixing is common: cup pulls on drawers, bar pulls or knobs on doors.

Base material is zinc, a cast alloy that takes the rustic Siena detailing crisply and stands up to normal cabinet cycling. For a heavier-duty spec, the solid brass options ZenSupply carries include the Deltana SBP35 and the Omnia 1968, 1969, 1970 and 1971 forged solid brass pulls. Forged brass is the usual call where a property manager is fitting out many units and wants one finish that will not chip.

Two: Ancient Bronze (ABZ) and Vibra Nickel (VN). Ancient Bronze is the darker, warmer option that suits the rustic Siena styling; Vibra Nickel is the brushed silver-tone. If you are matching cabinetry across a whole job, pick one and order the full count, because those are the only two finishes the 254 is made in.

The Schaub 254 Siena cup pull has a zinc base material. If a solid brass body is what the spec calls for, the Omnia 1969, 1970, and 1971 cabinet pulls are forged solid brass, as is the Deltana SBP35 square bar pull. Those are all bar-style pulls rather than cup pulls, so the grip changes from a recessed cup to a straight bar, and their hole spacing has to be confirmed against the 3 inch boring the 254 uses.

Emtek builds a Schaub Collection line that carries the same design family in other forms: the Emtek 8405 Select cabinet pull, the Alexander cabinet pull, the Art Deco cabinet pull, and the Bar cabinet pull are all Schaub Collection cabinet knob and pull styles. Cup pulls like the Schaub 254 Siena are normally used on drawers where the hand comes up from underneath, so pairing drawer cup pulls with a knob or bar pull from the same family on doors is the usual way to run a kitchen or casework package.

A knob is a single-screw part and the Schaub 254 Siena cup pull mounts on two screws at 3 inch center to center, so a knob does not cover the existing pair of holes. Orca Hardware knobs such as the CK-15030 round knob at 1-1/4 inch diameter, the CK-16030 round ring knob at 1-1/4 inch diameter, and the CK-17025 square knob at 25mm are cabinet knobs, and going that direction on drawers already bored for the 254 means plugging and refinishing the fronts or replacing them.

The Schaub 254 Siena cup pull is zinc with a 1 inch projection and a 1-3/4 inch overall dimension, sized for residential-scale casework and rustic-styled millwork. Where the application is a shop or breakroom taking constant use, the Deltana SBP35 is described as a heavy-duty solid brass square bar pull, and the Orca CK-12001 T-pull bar is steel with a 2 inch bar width. Both give a full-hand grip rather than the fingertip cup grip of the 254.

Overall length of the Schaub 254 is 1-3/4 inches with the mounting holes 3 inches apart, so the footprint is compact and it sits comfortably on narrow drawer fronts where a long bar pull would crowd the edges. Check that you have at least a couple of inches of face height, since the pull projects 1 inch and needs finger room underneath.

The Schaub 254 Siena cup pull projects 1 inch off the drawer face. Among comparable cabinet pulls, the Omnia 1969 and Omnia 1971 project 1-3/16 inch and the Omnia 1970 projects 1-1/4 inch. In tight galley runs, inside corner cabinets, or anywhere an adjacent door swings past the drawer bank, that difference decides whether the hardware clears, so check the projection before switching families.