Schaub 529 12" Center to Center Menlo Park Arched Cabinet Pull

Two holes 12 inches apart on center. The Menlo Park 529 arched pull measures 12-1/2 inches overall, so it only overhangs about a quarter inch past each mounting hole. On a replacement job the existing bores have to be a true 12 inch spread; there is no adjustment in the pull.

It takes 8/32 machine screws at 1 inch length. One inch of screw covers a standard 3/4 inch front with thread left to engage the post. If you are mounting to a thicker slab front or doubling up a shaker overlay, you will need longer 8-32 screws.

The Schaub 529 Menlo Park arched pull is a zinc-base pull with a 12 inch center-to-center spacing and a 1-1/4 inch projection. If you want forged solid brass instead of zinc, the Omnia 1970 modern cabinet pull is forged solid brass and also carries a 1-1/4 inch projection, so the standoff off the door face matches. The Omnia 1969 and Omnia 1971 are also forged solid brass modern pulls, both at a 1-3/16 inch projection, which is a sixteenth tighter to the face. Confirm the center-to-center you need in the Omnia series, since the 529 is specifically a 12 inch spread.

The Schaub 529 Menlo Park is built around a 12 inch center-to-center spread with a 12-1/2 inch overall length, which suits tall pantry doors and appliance panels rather than small drawers. For short drawer fronts, the Trimco 553 series drawer pulls are 3 inch center-to-center, and the Trimco 562 series offers 3-1/2 inch, 4 inch, and 96mm center-to-center options. The Deltana SBP35 modern square bar pull is a 3-1/2 inch solid brass option in the same short range. Note these are different styles from the Menlo Park arched profile, so mixing them in one room is a design decision.

No. The Omnia 1968/102 is a forged solid brass modern cabinet pull on 4 inch center-to-center spacing, while the Schaub 529 Menlo Park is on 12 inch centers with a 12-1/2 inch overall length. The mounting holes will not line up on an existing front bored for the 529. Use the 1968/102 where you are boring fresh cabinetry for a 4 inch spread, not as a swap.

Seven: Satin Nickel, Brushed Nickel, Polished Nickel, Polished Chrome, Matte Black, Ancient Bronze, and Signature Satin Brass. If you are matching existing kitchen hardware, note that Satin Nickel and Brushed Nickel are separate finishes here, so pull the code off the original order rather than eyeballing it.

Yes, if you do not need the long arched profile. The Schaub 529 Menlo Park is a two-hole pull on 12 inch centers, so swapping to a knob means only one hole and new boring. Orca Hardware's Bachelor Collection CK-15030 is a 1-1/4 inch diameter round cabinet knob, the CK-16030 is a 1-1/4 inch round ring knob, and the Blackcomb CK-17025 is a 25mm square knob. Any of these changes the hole pattern from the 529's two-screw layout, so plan on patching the second hole on existing fronts.

The Schaub 529 Menlo Park is a transitional arched pull with a 3/4 inch base dimension and a zinc base material. For a squarer, more contemporary line, the Orca Hardware CK-12001 T-pull bar is a steel pull with a 2 inch bar width in satin nickel, and the Deltana SBP35 is a modern square bar pull in solid brass. Both read as straight bar hardware rather than the arched Menlo Park profile, so use one or the other across a run rather than mixing.

Schaub styles the Menlo Park 529 as transitional, meaning the arched bar reads clean without the hard edges of a straight modern bar. Against it, the Omnia 1968, 1969, 1970 and 1971 pulls and the Deltana SBP35 square bar are classed as modern, and Emtek's Art Deco and Alexander pulls go period. For shaker or inset doors in a mixed traditional-contemporary room, the arch is the safer pick.

Yes. Schaub publishes a Proposition 65 warning for this pull through its product stewardship page, which matters if you are shipping into California or filling out submittals for a California project.