Schaub 536 8" Center to Center Menlo Park Cabinet Pull

Zinc is the base material on the 536. That is a cast, plated pull rather than a forged brass one. If your spec calls for solid brass, the Omnia 1968, 1969, 1970 and 1971 cabinet pulls are forged solid brass, and the Deltana SBP35 square bar pull is solid brass at 3-1/2 inches.

The Schaub 536 Menlo Park is fixed at 8 inch center-to-center with an 8-1/2 inch overall length, so it needs a drawer front wide enough to carry it. For narrower fronts, the Trimco 553 drawer pull is 3 inch center-to-center, the Trimco 562 comes in 3-1/2 inch, 4 inch, and 96mm center-to-center, the Deltana SBP35 square bar pull is 3-1/2 inch, and the Omnia 1968/102 is a 4 inch center-to-center modern pull. Mixing an 8 inch pull on wide drawers with a shorter one on narrow drawers is common; the shorter part will need its own bore pattern, not the 536 holes.

The Menlo Park 536 uses 8/32 machine screws, the standard cabinet hardware thread. If you're pulling it onto a thick applied-panel or false front, buy longer 8/32 screws in the length you need; the thread size is what has to match, not the screw that ships in the bag.

Just the one. The Menlo Park 536 is built at 8 inch centers and 8-1/2 inches overall, and the only choice you make when ordering is finish. To mix sizes across a kitchen you'd pair it with other pulls in the range rather than a shorter 536.

No - the Schaub 536 is a two-hole cabinet pull at 8 inch center-to-center, and a knob mounts on a single bore. Knobs such as the Orca Hardware CK-15030 round Bachelor Collection knob at 1-1/4 inch diameter, the CK-16030 round ring knob at 1-1/4 inch, and the CK-17025 Blackcomb square knob at 25mm are single-point cabinet knobs, so swapping one in leaves an open hole from the 536 pattern. Knobs are a reasonable choice on doors and small drawers where a pull was never bored, not as a replacement for an existing 8 inch pull.

The Schaub 536 Menlo Park has a zinc base material. Where a specifier wants solid brass on the same cabinet run, the Deltana SBP35 is a heavy-duty solid brass square bar pull, and the Omnia 1968/102, 1969, 1970 and 1971 are forged solid brass modern pulls. Brass and zinc take finishes differently, so if part of a fleet stays on the 536 in Satin Nickel or Matte Black, order a sample of the substitute in the same finish family before committing the whole property.

The Schaub 536 is part of the Menlo Park collection. Emtek carries Schaub collection cabinet pulls under its own part numbers, including the Emtek 8405 Select cabinet pull, the Emtek Alexander cabinet pull, the Emtek Art Deco cabinet pull, and the Emtek Bar cabinet pull. Those are separate series - Select, Alexander, Art Deco, and Bar - rather than Menlo Park, so they are style siblings within the same design family and not a drop-in match for the 536 profile.

Seven: Satin Nickel, Brushed Nickel, Polished Nickel, Polished Chrome, Ancient Bronze, Matte Black, and Signature Satin Brass. That is the full run, so if you're matching an existing kitchen the decision is usually between the three nickels, which read differently under warm lighting.

The Schaub 536 Menlo Park is a transitional cabinet pull with a 1 inch base dimension, 1-1/8 inch projection, and 8/32 screw thread, sized for cabinet and drawer fronts. The Orca Hardware CK-12001 is a T-pull bar in steel with a 2 inch bar width, a different profile aimed at bar-pull applications. They are not interchangeable on the same bore or the same screw hardware, so decide the profile before the fronts are drilled.