Schaub 559 24" Center to Center Heathrow Appliance Pull

Yes, the Schaub 559 Heathrow is drilled on 24 inch center-to-center, so it drops onto an appliance panel already bored at 24 inches. The pull itself measures 26-1/2 inches overall, so you need at least that much clear panel or door face beyond the mounting holes, 1-1/4 inches past each hole.

The 559 Heathrow uses #8-32 x 1 inch machine screws, which is the standard cabinet-hardware thread. One inch of screw covers a typical 3/4 inch panel with thread left to engage the post. On a thicker custom overlay panel or a fridge with a heavy false front, you'll need longer #8-32 screws, which is the same thread so replacements are easy to source.

Back-to-back mounts two pulls through the same holes, one on each face of the panel, sharing the through-bolts. It's what you specify for a glass door, a pass-through, or a swinging door where you want a matching grip on both sides. Ordered as No, you get the single-sided pull mounted with the standard screws. The 559 is offered either way in all five finishes.

The Schaub 559 Heathrow is an appliance pull with 24 inch center-to-center spacing and a 26-1/2 inch overall length, which is sized for a refrigerator or panel-ready appliance front rather than a cabinet door. For ordinary cabinet doors and drawers, the Omnia 1968/102 is a modern cabinet pull in forged solid brass with 4 inch center-to-center spacing, and the Trimco 553 Series drawer pull is offered at 3 inch center-to-center. Both are small-bore drawer and door pulls, not appliance-scale hardware.

The Schaub 559 Heathrow is fixed at 24 inch center-to-center. For shorter drawer fronts, the Trimco 562 Series drawer pull is offered in 3-1/2 inch, 4 inch and 96mm center-to-center, the Trimco 553 Series at 3 inch, the Deltana SBP35 at 3-1/2 inch and the Omnia 1968/102 at 4 inch. Measure the existing hole spread before ordering, since these are drilled to fixed centers.

Projection is 2 inches, measured from the face of the panel to the back of the grip bar. That's enough knuckle clearance for a gloved hand on a refrigerator or a full-height pantry door. In a tight galley run, check that 2 inches clears any adjacent wall or return cabinet when the door swings.

Five: Polished Chrome (PC), Brushed Nickel (BN), Matte Black (MB), Polished Nickel (PN), and Signature Satin Brass (SSB). Every one of those is available in both the single and back-to-back configuration, so a kitchen that mixes a single-sided fridge pull with a back-to-back pantry door still matches.

It's catalogued as an appliance pull because of the 24 inch centers and 2 inch projection, but nothing restricts it to a refrigerator. The same pull works on a tall pantry door, a full-height utility cabinet, or a door with a matching applied panel. For drawers and standard cabinet fronts you want much shorter centers, the Trimco 553 Series at 3 inch ctc or the Trimco 562 Series in 3-1/2 inch, 4 inch and 96mm being typical drawer spacings.

The Schaub 559 Heathrow is solid brass in a contemporary style. Where a steel bar pull suits the budget or the look, the Orca Hardware CK-12001 T-pull bar is steel with a 2 inch bar width in satin nickel. It is a bar pull rather than an appliance pull, so confirm the mounting spread against the 24 inch center-to-center the 559 uses.

The base measures 1 inch. If you're replacing an existing appliance pull, that 1 inch footprint only hides a previous hole if the old centers were within about a half inch of 24 inches. Anything further off and you're patching and re-drilling the panel.

No. The SDC SP50 is a 50mm spindle used in door control hardware, not cabinet hardware. The Schaub 559 Heathrow mounts with #8-32 x 1 inch screws through the door or appliance panel and needs no spindle.