Schaub 560 3-1/2" Center to Center Heathrow Cabinet Pull

It mounts with #8-32 machine screws 1 inch long, the standard cabinet hardware thread. One inch handles a typical 3/4 inch drawer front or door with thread left to engage the pull. If you are going through a 5-piece front, a thick slab, or a front with an applied panel, you will need longer #8-32 screws.

The Schaub 560 Heathrow is fixed at 3-1/2 inch center-to-center, so it will not land on 4 inch bores. The Omnia 1968/102 modern cabinet pull is forged solid brass with 4 inch center-to-center spacing, and the Trimco 562 Series drawer pull is offered in a 4 inch center-to-center option as well as 3-1/2 inch and 96mm. Either lets you keep existing holes on the wider drawers while running the Schaub 560 on doors drilled at 3-1/2 inch.

The Deltana SBP35 Modern Square Bar Pull is also a 3-1/2 inch solid brass bar pull, so it lands on the same hole spacing as the Schaub 560 Heathrow and can reuse existing drilling. The Trimco 562 Series drawer pull is another option at 3-1/2 inch center-to-center, and it also comes in 4 inch and 96mm spacings if part of the run uses different hole centers. The Schaub 560 is solid brass with a 1-1/4 inch projection and a 5-1/4 inch overall length, so compare projection and overall length against those two before swapping, since a matching bore spacing does not guarantee matching reach off the door face.

Projection is 1-1/4 inches off the face of the door or drawer, with a 3/4 inch base where it meets the surface. That 1-1/4 inch standoff gives good knuckle room, but check it against appliance handles, adjacent walls, and inside corner cabinets where a pull can collide with the run beside it.

Solid brass base material, not zinc die-cast. For a multi-unit or hospitality job that matters: solid brass takes daily pulling without the base cracking at the post, and the finish is applied over brass rather than pot metal.

The Deltana SBP35 Modern Square Bar Pull is a heavy-duty solid brass pull at 3-1/2 inches, so it lands on the same hole spacing with the same base material. Difference is the look: the Deltana is a square bar profile, while the Heathrow is Schaub's contemporary Heathrow collection shape at 1-1/4 inch projection.

The Schaub 560 Heathrow projects 1-1/4 inch off the face. If you need the handle to sit closer to the door, the Omnia 1969 and Omnia 1971 modern cabinet pulls are forged solid brass with a 1-3/16 inch projection, which pulls the bar in slightly. The Omnia 1970 is also forged solid brass but matches the Schaub at 1-1/4 inch projection, so it is a styling alternative rather than a clearance fix. All three are in Omnia's modern cabinet pull series, in keeping with the contemporary look of the Heathrow.

No. The Trimco 553 Series drawer pull is a 3 inch center-to-center pull, while the Schaub 560 Heathrow is 3-1/2 inch center-to-center, so the bores do not line up. If you are working to existing 3-1/2 inch holes, stay with the Schaub 560 or look at the Trimco 562 Series, which includes a 3-1/2 inch center-to-center option.

Five: Polished Chrome, Brushed Nickel, Polished Nickel, Matte Black, and Signature Satin Brass. If you are matching an existing kitchen or a whole building, order all of it from the same finish code - Polished Nickel and Polished Chrome read very differently side by side, one warm and one blue-white.

Schaub designs are also carried under Emtek's Schaub Collection, including the Emtek 8405 Select cabinet knobs and pulls, which are catalogued as knob/pull. If you want a plain round knob instead, the Orca Bachelor Collection round cabinet knob is 1-1/4 inch diameter, which reads in proportion next to a 5-1/4 inch pull.