Schaub 880 12" Center to Center Empire Appliance Pull

Only if your panel is drilled 12 inches on center. The Schaub 880 Empire appliance pull is a 12 inch center-to-center pull, so the two mounting holes have to sit exactly 12 inches apart. Overall length is 13-1/8 inches, which means about a half inch of pull extends past each hole, so allow for that at the panel edges.

The Schaub 880 is an appliance pull with 12 inch center-to-center spacing and a 13-1/8 inch overall length, drawn in the Empire collection in a transitional style. For a plainer bar profile on the same kind of appliance panel, the Emtek Bar Cabinet Pull in the Schaub Collection carries a straight bar form, and the Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width in steel with a satin nickel finish. Confirm the hole spacing you need before ordering, since the 880 is specifically drilled for 12 inch centers.

The Schaub 880 is built as an appliance pull at 12 inch center-to-center with 1-5/8 inch projection, which is far wider than typical drawer hardware. For cabinet drawers, the Trimco 553 Series drawer pulls are offered at 3 inch center-to-center and the Trimco 562 Series at 3-1/2 inch, 4 inch, and 96mm center-to-center, and the Omnia 1968/102 is a forged solid brass cabinet pull with 4 inch center-to-center spacing. Those cover drawer fronts; the 880 is drilled for the wide spacing an appliance panel uses.

Projection is 1-5/8 inches from the face of the door or panel to the back of the grip, with a 1-1/8 inch base. That is enough hand clearance for a full grip on a heavy refrigerator or freezer panel, but check it against anything nearby, a return wall, a trim casing or an adjacent appliance handle, before you set the panel position.

You need the panel drilled at 12 inch centers and screws long enough for your panel thickness, since appliance panel thickness varies by manufacturer and by whether you are through-bolting a wood panel or tapping a factory stainless door. Confirm the fastener length against your panel before drilling, because the 12 inch hole spacing cannot be adjusted after the fact.

The Schaub 880 is an Empire collection appliance pull offered in Satin Nickel, Polished Chrome, Ancient Bronze, Antique Nickel, Brushed Bronze, Brushed Nickel, Empire Bronze, Matte Black, Polished Nickel, and Signature Satin Brass. To carry a Schaub-family look onto the smaller openings, the Emtek 8405 Select cabinet pulls, the Emtek Alexander cabinet pull, and the Emtek Art Deco cabinet pull are all Schaub Collection cabinet knob/pull items. Verify finish names line up between the two brands before standardizing a kitchen.

The Schaub 880 Empire appliance pull uses a zinc base material. If a solid brass body is specified, the Deltana SBP35 Modern Square Bar Pull at 3-1/2 inch is heavy-duty solid brass, and the Omnia 1969, 1970, and 1971 modern cabinet pulls are forged solid brass, with 1-3/16 inch projection on the 1969 and 1971 and 1-1/4 inch on the 1970. Those brass options are cabinet-scale pulls rather than 12 inch appliance-width hardware.

No. The Schaub 880 is a two-post appliance pull with 12 inch center-to-center spacing, so it needs two bored holes at that spacing. Single-hole knobs such as the Orca Hardware Bachelor Collection round cabinet knob at 1-1/4 inch diameter, the Bachelor Collection round ring knob at 1-1/4 inch diameter, and the Blackcomb Collection square knob at 25mm diameter mount on one hole and cannot fill an existing 12 inch two-hole pattern.

The Empire collection is styled transitional, so it sits between traditional and contemporary and pairs with either direction without looking out of place. If you want a strictly modern kitchen, a straight bar profile such as the Emtek Bar cabinet pull or the Omnia 1970 series is the cleaner match.

Yes. Empire is a Schaub collection, so the 880 appliance pull is drawn from a family with matching smaller pulls and knobs in the same finishes. Schaub hardware is also carried under the Emtek SELECT program as the Schaub Collection, which is worth knowing if your cabinet order is being placed through an Emtek specification.