Metallics JRM94SLT 10-24 x 1-1...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$50.21
$0.21
Metallics JRM94SLT 10-24 x 1-1/4 in. Round Head Slotted Machine Screws - Steel Zinc - 100qty

Metallics JRM94SLT 10-24 x 1-1/4 in. Round Head Slotted Machine Screws - Steel Zinc - Each

(No reviews yet) Write a Review

Model: JRM94SLT
Selected Model is

In Stock (leaves warehouse same day if ordered before 3pm ET)

$50.21
$0.21
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
10-24 x 1-1/4 in. Round Head Slotted Machine Screws - Steel Zinc - 100qty

  • Additional Notes

    • In 1985, Metallics was the first fastener company in America to offer a full line of Combo’s! | Other sizes and quantities available by request | Tensile strength values for stainless screws are offered as approximations only; there is no single standard for the performance requirements of stainless machine screws.

  • Features

    • Round head with slotted Drive
    • 10-24 Diameter, 1-1/4" Length
    • Steel Zinc Material

Manufacturer Resources

Product Specs

Minimum Purchase:
100 units
Arra Compliant:
C
Buy American Compliant:
C
Division:
Electrical H1
Drive Type:
Slotted
Fastener Head Height:
0.123 - 0.137 in.
Fastener Head Type:
Round
Fastener Head Width:
0.334 - 0.359 in.
Fastener Length:
1/1/04
Hardness:
Rockwell B70-B100
Language Code:
EN
Material Standard:
AISI 1006 - 1022
Neurspe:
https://ideadigitalasset.com/DAMRoot/Original/10035/11237_ID-SPE-v1-ID-SPE-v1-Round_Head_Machine_Screw.pdf
Order Minimum Imperial:
100
Order Minimum Uom Imperial:
CT
Pack Type:
Jar
Product Group:
Fasteners
Product Height:
2.15 in
Product Length:
3 in
Product Weight:
0.95 lbs
Product Width:
3 in
Recess Penetration Gaging Depth:
0.082 - 0.108
Slot Depth:
0.065 - 0.087
Slot Width:
0.05 - 0.06
Sub Division:
Electrical-E H2
Tensile Strength:
60000 psi minimum
Thread Per Inch:
24
Department:
Electrical
Product Subgroup:
Screws
Product Type:
Machine Screw
Type2:
Machine Screw
Series:
JRM
Product Finish:
Zinc
Product Details:
Machine Screw
Product Material:
Steel Zinc

Metallics JRM94SLT – Frequently Asked Questions

1) Do these Metallics machine screws meet Buy American and ARRA requirements on a public job?
Metallics lists the JRM94SLT as both ARRA compliant and Buy American compliant. Country of origin is China. On a federal or state funded project where the specification calls out a domestic melt and manufacture requirement rather than the ARRA/BAA compliance designation, confirm which standard your spec is written to.
2) How many screws come in a pack of the Metallics JRM94SLT?
They ship 100 to a jar, and 100 count is the order minimum. Package weight is listed at 0.95 lbs. If you need a different count, Metallics offers other sizes and quantities by request.
3) Is a round head slotted screw the right choice, or should I use a flat head?
Round head sits proud on the surface with a domed crown, so use it where the screw head can stand above the material and you want full bearing on the part being held. Head width runs 0.334 to 0.359 in. and head height 0.123 to 0.137 in. If the head has to sit flush in a countersunk hole, you want a flat head instead, not this one.
4) Are these zinc plated screws OK for damp or outdoor locations?
The JRM94SLT is carbon steel with a zinc finish, which handles indoor and protected locations well but is not a marine or sustained wet-location material. For exterior exposure, washdown areas, or coastal work, step up to a stainless machine screw in the same 10-24 x 1-1/4 in. size.
5) What is the strength rating on these 10-24 steel machine screws?
Minimum tensile strength is 60,000 psi, with hardness of Rockwell B70 to B100, made from AISI 1006 to 1022 low carbon steel. That is standard commercial grade machine screw material, fine for device mounting, panel work, and general fastening. It is not a graded structural fastener, so do not substitute it where a drawing calls for a Grade 5 or Grade 8 bolt.
6) Will a 10-24 machine screw work in a tapped hole or do I need a nut?
A machine screw has a uniform straight machine thread, so the JRM94SLT works either way: threaded into a tapped 10-24 hole, or run through a clearance hole with a 10-24 nut behind it. It is not a self-tapping or sheet metal screw, so it will not cut its own thread in an untapped hole.
7) Is the 1-1/4 inch length the shank or the overall screw length?
On a round head machine screw the 1-1/4 inch length is measured from the underside of the head to the point, so the domed head height, 0.123 to 0.137 in., sits on top of that. Allow for it when you are figuring stack-up through a ring and into a tapped strap.
How fast can I get the Metallics JRM94SLT delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JRM94SLT come with a warranty?
Absolutely. The Metallics JRM94SLT is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JRM94SLT?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Metallics JRM94SLT from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!