Metallics TSP29M 10 x 1-1/4 in...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$50.14
$0.14
Metallics TSP29M 10 x 1-1/4 in. Pan Head Phillips Sharp Point Tapping Screws - Steel Zinc - 1000qty

Metallics TSP29M 10 x 1-1/4 in. Pan Head Phillips Sharp Point Tapping Screws - Steel Zinc - Each

(No reviews yet) Write a Review

Model: TSP29M
Selected Model is

In Stock (leaves warehouse same day if ordered before 3pm ET)

$50.14
$0.14
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
10 x 1-1/4 in. Pan Head Phillips Sharp Point Tapping Screws - Steel Zinc - 1000qty

  • Features

    • Pan head with Phillips Drive
    • Steel Zinc Material
    • 10 Diameter, 1-1/4" Length

  • Additional Notes

    • Other sizes and quantities available by request | Dimensions for #9 diameter are independent of ASME B18.6.4

Manufacturer Resources

Product Specs

Minimum Purchase:
1000 units
Arra Compliant:
N
Buy American Compliant:
No
Dimensional Standard:
ASME B18.6.3-2013
Division:
Electrical H1
Drive Type:
Phillips
Driver Size:
#2
Fastener Head Height:
0.122 - 0.133 in.
Fastener Head Type:
Pan
Fastener Head Width:
0.357 - 0.373 in.
Fastener Length:
1/1/04
Hardness:
Rockwell C28 - 38
Language Code:
EN
Material Standard:
AISI 1016 - 1024
Order Minimum Imperial:
1000
Order Minimum Uom Imperial:
TH
Pack Type:
Box
Phillips Recess Depth:
0.124
Phillips Recess Diameter:
0.186 - 0.199
Phillips Recess Width:
0.031
Product Group:
Fasteners
Screw Point Type:
Gimlet Point
Sub Division:
Electrical-E H2
Thread Per Inch:
12
Thread Standard:
ASME B18.6.4
Torsional Strength:
48 lb-in minimum
Department:
Electrical
Product Subgroup:
Screws
Product Type:
Type A Tapping Screw
Type2:
Type A Tapping Screw
Series:
JTSP
Product Finish:
Zinc
Product Details:
Type A Tapping Screw
Product Material:
Steel Zinc

Metallics TSP29M – Frequently Asked Questions

1) Is the TSP29M a self-drilling screw or do I need to pre-drill?
It's a Type A tapping screw with a gimlet (sharp) point, not a self-drilling screw. The sharp point starts in thin sheet metal, wood, and fiberboard on its own, but it has no drill flute, so thicker gauge steel needs a pilot hole. For heavier steel you want a Type AB/B with a pilot or a true self-drilling point.
2) Do these Metallics screws meet Buy American or ARRA requirements for a public project?
No. The TSP29M is not Buy American compliant and not ARRA compliant, with country of origin listed as multiple. If your job carries a domestic sourcing clause, this screw won't satisfy it.
3) What driver bit do I need for the Metallics TSP29M tapping screws?
A #2 Phillips bit. The TSP29M has a Phillips recess sized 0.186 to 0.199 in. diameter and 0.124 in. deep, which is the #2 range. A #1 will cam out and a #3 won't seat.
4) Will a #10 x 1-1/4 pan head screw sit flush, or does the head stand proud?
A pan head sits on top of the surface. The TSP29M head measures 0.357 to 0.373 in. across and 0.122 to 0.133 in. high, so expect roughly an eighth of an inch standing above the work. If you need the head buried, use a flat head screw in a countersunk hole instead.
5) How tough are these screws? I keep snapping heads off with an impact driver.
The TSP29M is hardened to Rockwell C28-38 with a 48 lb-in minimum torsional strength, made from AISI 1016-1024 steel. That's standard case-hardened tapping screw territory, enough for sheet metal work, but an impact driver will exceed 48 lb-in easily. Run them with a clutched drill-driver and back off the torque.
6) Can I use these zinc plated tapping screws outdoors?
Zinc plated carbon steel is a dry, indoor-protected finish. It holds up fine in panels, enclosures, and interior framing, but in exterior or damp locations it will rust. For outdoor or wet work go stainless or a hot-dip galvanized fastener.
7) Do I have to buy a full box of 1000 TSP29M screws?
Yes. The TSP29M ships as a box with a 1,000 piece minimum, so it's a bulk MRO or panel-shop buy rather than a handful. Other sizes and quantities in the line are available by request.
8) What thread pitch is the #10 Metallics tapping screw?
12 threads per inch, per ASME B18.6.4 tapping screw threading. That's the coarse Type A spacing that lets the screw form its own thread in sheet stock rather than matching a machine screw nut.
9) What dimensional standard do these pan head screws conform to?
Head and recess geometry follow ASME B18.6.3-2013, and the threads follow ASME B18.6.4. That means the 0.357 to 0.373 in. head and #2 Phillips recess are to spec and interchange with any other conforming #10 pan head tapping screw. Note that #9 diameter screws in the line are dimensioned independently of ASME B18.6.4.
How fast can I get the Metallics TSP29M delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics TSP29M come with a warranty?
Absolutely. The Metallics TSP29M is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics TSP29M?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Metallics TSP29M from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!