Metallics JTEKD32M 12 x 2 in. ...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$50.50
$0.50
Metallics JTEKD32M 12 x 2 in. 5/16 Indented Hex Head Self-Drilling & Tapping Screws with Washer - #3 Drill Point - Steel Zinc - 1000qty

Metallics JTEKD32M 12 x 2 in. 5/16 Indented Hex Head Self-Drilling & Tapping Screws with Washer - #3 Drill Point - Steel Zinc - Each

(No reviews yet) Write a Review

Model: JTEKD32M
Selected Model is

In Stock (leaves warehouse same day if ordered before 3pm ET)

$50.50
$0.50
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
12 x 2 in. 5/16 Indented Hex Head Self-Drilling & Tapping Screws with Washer - #3 Drill Point - Steel Zinc - 1000qty

  • Additional Notes

    • Other sizes and quantities available by request. | SAE J78 does not include Specifications for #7 diameter drill screws. | This table is only a guide and does not constitute a warranty of any type.

  • Features

    • 5/16 Indented Hex Head with Hex Drive
    • #3 Drill Point
    • Steel Zinc Material
    • Minimum torques are the same for stainless and steel self-drill screws. Drill time is 2.5 seconds for a 1 mm thick plate.
    • 12 Diameter, 2" Length

Manufacturer Resources

Product Specs

Minimum Purchase:
1000 units
Arra Compliant:
C
Buy American Compliant:
C
Dimensional Standard:
ASME B18.6.3-2010
Division:
Electrical H1
Drill Point Size:
#3
Drive Type:
Hex
Fastener Head Height:
0.139 - 0.155 in.
Fastener Head Type:
Indented Hex
Fastener Head Width:
0.305 - 0.312 in.
Fastener Length:
2
Hardness:
Rockwell C32-40
Language Code:
EN
Material Standard:
AISI 1016 - 1024
Neurspe:
https://ideadigitalasset.com/DAMRoot/Original/10035/11237_ID-SPE-v1-ID-SPE-v1-Hex_Head_Self-Drill_TS_Indent_Hex_Washer.pdf
Order Minimum Imperial:
1000
Order Minimum Uom Imperial:
TH
Pack Type:
Jar
Panel Thickness:
0.110 - 0.210 IN
Product Group:
Fasteners
Product Height:
7.25 in
Product Length:
4.5 in
Product Weight:
17.1 lbs
Product Width:
4.5 in
Screw Point Type:
Drill Point
Slot Depth:
0.077 - 0.093
Slot Width:
0.056 - 0.067
Sub Division:
Electrical-E H2
Thread Per Inch:
14
Thread Standard:
SAE J78 - 2013
Torsional Strength:
92 lb-in minimum
Washer Od:
0.398 - 0.432 in.
Washer Thickness:
0.022 - 0.039 IN
Width Across Corners:
0.34
Department:
Electrical
Product Subgroup:
Screws
Product Type:
Type BSD Self-Drilling & Tapping Screw
Type2:
Type BSD Self-Drilling & Tapping Screw
Series:
JTEKD
Product Finish:
Zinc
Product Details:
Type BSD Self-Drilling & Tapping Screw
Product Material:
Steel Zinc

Metallics JTEKD32M – Frequently Asked Questions

1) Will the Metallics JTEKD32M meet a Buy American requirement on a federal job?
The JTEKD32M is flagged compliant for both ARRA and Buy American, though country of origin is listed as China. If your specification is written to a domestic-melt-and-manufacture standard rather than the ARRA/Buy American flags, confirm the origin against your contract language.
2) What standards does this #12 self-drilling tapping screw meet?
Threads are made to SAE J78 - 2013 and head dimensions to ASME B18.6.3-2010, with steel per AISI 1016 - 1024 and a case hardness of Rockwell C32-40. Minimum torsional strength is 92 lb-in. Note that SAE J78 does not cover #7 diameter drill screws, so a submittal calling for that size cannot be satisfied to this standard.
3) Does this Metallics screw come with a sealing washer or a plain washer?
It is an integral washer head, not a separate gasket. Washer outside diameter is 0.398 to 0.432 inches with a thickness of 0.022 to 0.039 inches, so it spreads bearing load over the panel but does not seal against water. For weather-exposed work you want a bonded EPDM washer screw instead.
4) How many screws come in a jar of Metallics JTEKD32M, and can I buy fewer?
These ship in jar packaging with an order minimum of 1,000 pieces. If you need a smaller count for a single install, this is not the pack to buy, it is a bulk quantity intended for repeat use.
5) Is a zinc plated self-drilling screw okay for outdoor or damp locations?
These are steel with a zinc finish, which is fine for dry interior work such as strut, panel enclosures, and metal framing. Zinc plating gives limited corrosion protection, so for exterior, coastal, or wash-down areas specify a stainless self-drilling screw instead. Metallics notes minimum torque values are the same for stainless and steel self-drill screws, so switching material does not cost you drive strength.
6) Is a 2 inch long #12 self-drilling screw too long for attaching to 14 gauge strut?
The JTEKD32M is a #12 diameter, 2 inch length screw with 14 threads per inch. Two inches is long for a simple metal-to-metal lap, where excess shank just protrudes behind the panel. Use this length when you are fastening through a thicker standoff, sleeper, or stacked assembly and still need to reach steel in the 0.110 to 0.210 inch range. For a direct panel-to-panel connection, a 3/4 or 1 inch #12 is the usual pick.
7) How much does a 1000-count jar of Metallics JTEKD32M screws weigh?
Product weight is listed at 17.1 lbs, in a container measuring 7.25 x 4.5 x 4.5 inches. Worth knowing if you are staging multiple jars on a cart or a lift.
How fast can I get the Metallics JTEKD32M delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics JTEKD32M come with a warranty?
Absolutely. The Metallics JTEKD32M is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics JTEKD32M?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Metallics JTEKD32M from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!