Metallics QTEKD14V 8 x 1 in. 1...
IN STOCK (leaves warehouse same day if ordered before 3pm ET)
$50.44
$0.44
Metallics QTEKD14V 8 x 1 in. 1/4 Hex Head Quadrive Self-Drilling & Tapping Screws - #2 Drill Point - Domestic Steel Zinc - 500qty

Metallics QTEKD14V 8 x 1 in. 1/4 Hex Head Quadrive Self-Drilling & Tapping Screws - #2 Drill Point - Domestic Steel Zinc - Each

(No reviews yet) Write a Review

Model: QTEKD14V
Selected Model is

In Stock (leaves warehouse same day if ordered before 3pm ET)

$50.44
$0.44
Adding to cart… The item has been added
Free Shipping on orders over $199
We price match and offer bulk discounts! Click Add to Quote. It's quick and easy.
✨
Earn points with this purchase! You can redeem points for giftcards, iPads, XBox's and more. View Rewards
Free Keying on all locks
You may also like
8 x 1 in. 1/4 Hex Head Quadrive Self-Drilling & Tapping Screws - #2 Drill Point - Domestic Steel Zinc - 500qty

  • Features

    • 1/4 Hex Head with Quadrive Drive
    • 8 Diameter, 1" Length
    • Made in the USA
    • #2 Drill Point
    • Domestic Steel Zinc Material

Manufacturer Resources

Product Specs

Minimum Purchase:
500 units
Division:
Electrical H1
Fastener Head Type:
Hex
Product Group:
Fasteners
Screw Point Type:
Drill Point
Sub Division:
Electrical-E H2
Department:
Electrical
Product Subgroup:
Screws
Product Material:
Domestic Steel Zinc

Metallics QTEKD14V – Frequently Asked Questions

1) What size and length is the Metallics QTEKD14V self-drilling screw?
The QTEKD14V is a #8 diameter screw, 1 inch long, with a 1/4 inch hex head and Quadrive drive recess. The hex head lets you run it with a 1/4 inch magnetic nut driver, and the Quadrive recess gives you a square-drive backup if you'd rather use a bit.
2) Do I need to pre-drill a pilot hole for these hex head screws into metal studs?
No. The QTEKD14V has a #2 drill point, so it drills its own hole and taps its own thread in one pass. That is what the self-drilling and tapping designation means: set the screw, run it, done. No pilot hole and no separate tap.
3) Are Metallics QTEKD14V screws made in the USA for Buy American jobs?
Yes. The QTEKD14V is made in the USA from domestic steel with a zinc finish. That matters on federally funded and institutional work where domestic-origin fasteners are called out on the submittal.
4) What thickness of metal will a #2 drill point screw go through?
The #2 point on the QTEKD14V is the light-gauge point, intended for sheet metal and light steel rather than structural stock. With a 1 inch overall length, the usable drilling and clamping range is limited to thin material plus whatever you are fastening to it. For heavier steel, step up to a #3 or #5 point screw in a longer length.
5) Are these screws coated for corrosion resistance, and can I use them outdoors?
Material is domestic steel with a zinc finish. Zinc plating handles interior and dry service well, including metal stud framing, strut, and enclosure work. For sustained outdoor exposure or damp locations, a zinc-plated carbon steel screw is not the right choice; specify a stainless or a coated exterior-rated fastener instead.
6) What driver do I need to install 1/4 inch hex head Quadrive screws?
A 1/4 inch magnetic hex nut setter in a drill or impact driver is the normal way to run these. The Quadrive recess in the top of the head is a second option if the hex gets chewed or you are working in a spot where a nut setter will not seat. No specialty bit needed either way.
7) Will a hex washer head screw like this hold strap, clip, and plate without pulling through?
The 1/4 inch hex head gives a broader bearing surface than a pan or trim head, so it seats flat against straps, clips, channel, and box flanges without pulling through sheet material. It does not countersink, so it is not the screw to use where you need a flush surface.
8) What is the Metallics part number to reorder these screws?
Order by Metallics part number QTEKD14V. That designation covers the #8 x 1 inch, 1/4 hex head Quadrive self-drilling and tapping screw with the #2 drill point in domestic steel zinc.
How fast can I get the Metallics QTEKD14V delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the continental U.S. Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit, reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Metallics QTEKD14V come with a warranty?
Absolutely. The Metallics QTEKD14V is backed by a manufacturer’s warranty. For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Metallics QTEKD14V?
You can call, text, or email our expert support team for fast answers. We’re here to help with product selection, installation tips, and troubleshooting. Contact Us
Why buy the Metallics QTEKD14V from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support, and rewards on every order. Our team is always ready to help you choose the right product for your project.
!