Deltana DSHP916U10B-C Dome Door Stop High Profile, Solid Brass

Yes. The DSHP916 dome stop ships in an individual poly bag with mounting hardware included, sold one per unit. It is a floor mounted stop, so you are drilling into the finish floor or subfloor underneath the door swing.

Profile height is about where the door contacts the stop. The DSHP916 is the high profile dome, which stands taller off the floor and is the one to use when there is a gap under the door or when a low dome would slip under the door bottom instead of catching it. If your undercut is tight and you want the stop to sit close to the floor, a low rise dome like the Orca Hardware 23LP Series is the other direction.

The DSHP916 is a stop only; it takes the door's impact and does not latch it open. For hold-open, use the Orca Hardware 22HD Series goose neck floor stop, which is listed as a door holder, the Ives FS40 / FS41 / FS42 / FS43 automatic floor stop and holder, or the SOSS MDH magnetic door holder and stop. The Ives automatic units and the SOSS magnetic unit are both heavy duty.

The Deltana DSHP916 is a solid brass dome-style floor stop in a high profile. The closest same-shape alternatives are the Delaney Dome Door Stop (DLY-40260X), the Emtek 2251 Half Dome Door Stop, and the Ives FS17 heavy-duty brass floor dome stop with rubber bumper. All four mount to the floor and stop the door on a domed body, so any of them covers the same opening as long as the height you need clears the door bottom.

For a shorter reach to the door, the Orca Hardware 23LP Series dome floor stop is a low-rise dome with a gray tip, and the Emtek 2251 is a half dome. Both stop the door on the same domed geometry as the DSHP916 but present a lower body, which suits doors with little clearance above the floor.

That part number is the Oil Rubbed Bronze version. It is solid brass with the oil rubbed bronze finish applied, so it darkens and wears over time the way ORB hardware does, which matters if you are matching it to hinges and levers already on the opening.

Deltana classes the DSHP916 as commercial. It is solid brass rather than a plated zinc casting, which is what holds up in a corridor or entry that gets repeated door contact. For high traffic openings where you want a brass dome with a replaceable rubber bumper, the Ives FS13 is the heavy duty alternative.

Goose neck styles - the Delaney Gooseneck Floor Door Stop, the Emtek 2253 Goose Style Door Stop, and the Orca 22HD goose neck - are floor-mounted like the DSHP916 but use a tall curved arm rather than a dome, and the Orca 22HD is a holder rather than a stop. Straight cylindrical bumpers such as the Emtek 2257 1-1/2 inch cylindrical floor bumper, the Emtek 2254 floor door bumper at 1-3/8 inch by 1-1/4 inch, and the Sure-Loc DS-FL2 cylindrical floor stop are a different profile entirely. All contact the door at a different height and angle than a high-profile dome.

The DSHP916 is a solid brass stop designated for commercial use. Ives offers the FS13 and FS17 brass floor dome stops, both rated heavy duty, with the FS13 carrying a replaceable rubber bumper - worth noting if you maintain a facility and want to swap tips rather than the whole stop. Ives also lists the FS18S/FS18L security floor stop as heavy duty for openings where tampering is a concern.

It can be done, but the DSHP916 mounts with a fastener through the floor, so you are drilling the finish surface. On tile that means a masonry bit and care not to crack the glaze; on hardwood it leaves a permanent hole. If you cannot penetrate the floor, a wall mounted or hinge mounted stop is the better route, or a gooseneck style like the Emtek 2253 that still floor mounts but sets the fastener further back from the door path.

One. Unit of measure is each, and the price shown is per unit, each bagged individually with its hardware. If you are stopping a pair of doors you need two.

The DSHP916 is a solid brass commercial-designated dome stop. For lighter residential openings, the Sure-Loc DS-FL2 cylindrical floor stop is offered for residential doors, and the Sure-Loc DS-FL1 floor stop comes with a spring and modern door stop designs. Both mount to the floor in the same way but present a plainer profile than a high-profile brass dome.