Deltana DSW Wall Mount Bumper, 3-5/8"

3-5/8 inches is the bumper's stated size, so it stands the door off the wall by roughly that much less the depth of the door's own trim. That is a long projection by wall stop standards, and it is the reason to pick this one: it catches the door before a lever or a thumbturn hits the wall. Where a shorter stop would do, the Delaney 2-1/4 inch concave wall bumper covers that case.

The Deltana DSW325 is a solid brass wall-mounted bumper with a 3-5/8 inch projection. The nearest peer in the same style is the Emtek 2255 brass wall bumper with regular rosette, which is also a brass wall bumper. On the shorter side, the Delaney 40270X is a 2-1/4 inch concave wall bumper, so it sits closer to the wall and takes less projection off the door swing. If the finish match matters more than the exact projection, the Emtek 2255 is the closer swap; if you are trying to keep the bumper tight to the wall, the Delaney 2-1/4 inch is the one to look at.

The Deltana DSW325 is a solid brass wall bumper sized at 3-5/8 inches. For openings that see constant use and where the rubber will need service rather than replacement of the whole stop, the Ives WS11 is a heavy duty wall stop with a replaceable rubber bumper, rated for drywall and masonry, and the Ives WS33/WS33X is likewise a heavy-duty wall door stop with a replaceable rubber bumper. The ABH RM Series and RMS Series wall door stops are offered in multiple length options, which is what you want when the wall behind the door sits farther back than a standard bumper reaches. The Deltana gives you the brass finish family; the Ives and ABH units are the ones built around a serviceable bumper and length selection.

Commercial. The DSW325 is a solid brass wall mount bumper, and the description calls out heavier doors specifically as what these are for. Brass through the body rather than a plated pot metal casting is what makes that hold up on a door that gets thrown open dozens of times a day.

Nine finishes on the DSW325: PVD Polished Brass, Polished Brass, Antique Brass, Oil Rubbed Bronze, Brushed Nickel, Antique Nickel, Polished Chrome, Brushed Chrome, and Paint Black. If you are matching hinges and levers already on the openings, PVD Polished Brass is the one that holds its color rather than aging like standard polished brass, which matters on a part that gets kicked and wiped down.

Nothing for a standard install. Each DSW325 ships in its own poly bag with mounting hardware included, sold one per unit. The only thing you may add is a wall anchor suited to your substrate if the location does not fall on framing.

Different jobs. The DSW325 is a solid brass bumper in nine architectural finishes, so it is the choice when the stop has to match decorative trim. The Ives WS33 and WS11 are heavy duty wall stops with a replaceable rubber bumper, which is what an institutional buyer standardizes on when the bumper pad gets replaced rather than the whole stop. ABH RM and RMS series both come in multiple lengths if you need to tune the projection to the wall.

Not well. The DSW325 mounts to the wall, so it needs a flat surface at the height the door strikes. If the contact point falls on a baseboard or a wall you cannot drill, go to a floor or hinge mounted stop instead: the Delaney 3 inch HD rigid door stop and 3 inch spring door stop are the base mount options.

Both hold the door open, but the trigger differs. The Ives WS20 is a manual wall holder with a hinged strike - the strike is engaged by hand each time. The Ives WS40 is an automatic wall holder with a heavy duty bumper pad, catching the door as it swings without anyone setting it. The Ives WS40 is a light duty unit, while the WS20 is heavy duty. A wall bumper like the Deltana DSW325 does neither; it absorbs the swing at 3-5/8 inches and releases.

The Deltana DSW325 mounts to the wall, so it needs solid backing where the door lands. When the wall behind the door is not usable - a glass partition, a wall out of reach of the swing, a fixture in the way - the alternatives mount to the door or the floor instead. The Delaney 4021XX is a 3 inch heavy duty rigid door stop and the Delaney 40210X is a 3 inch spring door stop; both are the base-mounted style that works when there is no wall to strike. Check the swing before ordering, because a base-mounted stop changes where the door comes to rest.

No. The Delaney 2310011 is a 2-1/8 inch hole plate metal cover - it conceals an opening left in a wall or door, it does not take any impact. If you are pulling an old bumper and putting a new one in the same spot, the Deltana DSW325 is the brass wall bumper at 3-5/8 inches; the hole plate is what you use on the wall you are abandoning, to close the old fastener holes after the stop relocates.

For a facility standard, the question is whether you are matching finish or matching function. The Deltana DSW325 is a solid brass wall bumper carried in nine finishes including polished chrome, brushed nickel, oil rubbed bronze and antique brass, which is what lets it match trim across different areas of a building. For a single function standard across many openings, the ABH RM Series and RMS Series wall door stops are each offered with multiple length options, so one series covers walls at different distances from the door, and the Ives WS11 and WS33/WS33X carry a replaceable rubber bumper so the maintenance stock is a bumper rather than a complete stop.

The Deltana DSW325 is a wall mounted brass bumper packed with mounting hardware. Where the substrate is the deciding factor, the Ives WS11 and the Ives WS33/WS33X are heavy-duty wall stops specified for drywall and masonry, and the Ives WS20 manual wall holder is likewise offered for drywall and masonry applications. On a block or concrete wall, confirm the anchor before you set the stop - the fastener, not the bumper, is what carries the strike.

Solid brass, both material and substrate. That matters on a wall bumper more than most trim, because the part takes repeated impact and a plated finish over a soft base wears through at the contact face first. For a matching solid brass option from another brand, the Emtek 2255 brass wall bumper mounts with a regular rosette.

Individually. The DSW325 is sold each, one bumper per poly bag with its mounting hardware, so the count you order is the count of doors you cover. That makes it straightforward to standardize a fleet on one model and one finish across every opening.