Deltana FP828 Flush Pull, 4" x 1" x 1/2"

Pocket doors are one of its intended uses, along with sliding doors and cabinet doors. It sits flush with the door face so nothing protrudes into the pocket or the jamb when the door slides home. The recess it drops into needs to accept a 4 x 1 x 1/2 inch body, so the 1/2 inch is the depth you have to cut into the door.

The FP828 body measures 4 x 1 x 1/2 inches, so the 1/2 inch figure is what governs the recess depth. On a typical 1-3/8 inch interior door that leaves plenty of material behind the cup, but on a thin cabinet door or a hollow-core slab, check that you have solid stock to cut into before you rout.

Deltana sells the FP828 by the each, so one pull per unit ordered. A pocket door that is operated from both sides needs one on each face, and a pair of bypassing sliders normally takes one per leaf on the accessible side. Count your faces, not your doors, when you place the order.

No. The FP828 is a pull only, with no latch, no privacy function and no keying. It moves the door and nothing else. If the pocket door needs a privacy or passage function, that is a different part, for example the Baldwin Estate 8601 pocket door pull, which is made for passage and dummy applications. Plan on a separate pocket door latch set if you need to secure the opening.

The Deltana FP828 is a solid brass flush pull measuring 4 inches by 1 inch by 1/2 inch, made for face-flush installation in sliding, cabinet, and pocket doors. The Trimco 1059 is a drive-in flush cup pull, meaning the cup is driven into a bored hole rather than set into a routed mortise with a surrounding flange. Both give a flush face, but the 1059 series is prepped by boring and the FP828 is a rectangular mortise-and-plate pull.

The Deltana FP828 is a commercial solid brass flush pull for face-flush installation in sliding, cabinet, and pocket doors. It is not a ligature-resistant product. For a room where ligature resistance is the governing requirement, the ABH 1911 series is a flush door pull with a ligature-resistant design.

Solid brass throughout, not a plated stamping. That matters on a pull that gets fingered every day: the brass carries the finish through the section rather than sitting on top of a base metal, so an edge worn by a fingernail does not show a different metal underneath. Deltana rates it for commercial use.

Ten finishes: PVD Polished Brass, Polished Brass, Unlacquered Brass, Antique Brass, Oil Rubbed Bronze, Brushed Nickel, Antique Nickel, Polished Chrome, Brushed Chrome, and Paint Black. That covers the standard Deltana finish range, so if the levers and hinges on your other openings are Deltana you can carry the same finish onto the sliding and pocket doors. Unlacquered Brass will patina with handling; PVD Polished Brass will not.

The Deltana FP828 is a 4 inch flush pull. Where a bigger hand hold is wanted on the same kind of door, the Trimco 1111 series is a large flush cup pull, and the Trimco 1060/1061 is a standard flush cup pull. Both are cup style, so the pocket in the door is formed by the cup rather than by the flat rectangular body of the FP828.

Deltana lists the FP828 as commercial, and it is solid brass rather than a plated stamping, so it is used on office, hospitality and multi-family sliding and pocket doors as well as in homes. It is a pull with no latching function, so it does not carry an opening the way a lockset does.

The Deltana FP828 is offered in PVD Polished Brass, Polished Brass, Unlacquered Brass, Antique Brass, Oil Rubbed Bronze, Brushed Nickel, Antique Nickel, Polished Chrome, Brushed Chrome, and Paint Black, all on a solid brass body. That range covers both bright and aged looks from one part number, which is the usual reason to specify the FP828 over the Trimco 1060/1061 or 1111 flush cup pulls when the doors are being finished to match existing trim.