Deltana S41/4058R-S Special Hinges for Fiber Glass Doors, 4" x 4-1/4" x 5/8" Radius x Square Hinges, Security Stud, Steel (Pair)

The extra width is the point. The S41/4058R-S measures 4 x 4-1/4 inches, a wider throw than a standard 4 x 4, which is what fiberglass entry doors with thick brickmould or heavy weatherstrip need so the door can swing clear of the trim. If your existing hinge is a plain 4 x 4 and the door binds on the casing when it opens, this is the swap that buys you the clearance.

Yes, handing matters on this one. The S41/4058R-S comes left hand (LH) or right hand (RH), because the corner style is mixed: one leaf has 5/8 inch radius corners and the other has square corners, so the leaves are not interchangeable side to side. Stand outside the door, on the side it swings away from you; if the hinges are on your left it is left hand.

It is a security tab, a stud on one leaf that seats into a matching hole on the other when the door is closed. With the door shut, the leaves are mechanically interlocked, so pulling the pin will not let an intruder lift the door out of the frame. Worth noting: the pin itself is a standard removable pin, not an NRP, so the stud is what is doing the anti-removal work here.

No. The S41/4058R-S is a residential-duty plain bearing steel hinge, meant for fiberglass entry doors on homes and low-traffic multi-family units. For a commercial door seeing constant cycling you want a ball or concealed bearing hinge instead, such as the Ives 3CB1HW heavy weight concealed bearing full mortise hinge or the Don-Jo HWBB74545 at 4-1/2 x 4-1/2 inches.

It will if the door leaf pocket is routed for 5/8 inch radius corners and the frame leaf pocket is square, which is how most factory-prepped fiberglass entry systems come. It is a full mortise hinge, so both leaves sit in routed pockets. If both of your existing pockets are square corner, this is the wrong corner combination and you want a square x square hinge instead.

The Deltana S41/4058R-S carries a security stud (security/locking tab) and is classed residential. For a commercial opening where the pin itself must be defeated, the Hager BB1168-NRP is a full mortise ball bearing heavy duty hinge supplied with a non-removable pin; the Deltana is not an NRP hinge, so its pin can still be driven out. For detention-level work the BEST BB855 and the Stanley Security BB855 are double weight prison hinges, the Stanley in 5 inch by 6 inch. Those are different classes of product, not drop-in replacements for a 4 by 4-1/4 residential leaf.

The S41/4058R-S is sold by the pair, so a typical three-hinge exterior fiberglass door takes two pairs, which leaves you a spare leaf set, or you buy two pairs per door and keep the extra for the next opening. Both leaves of each pair carry the matching handing, so order all of them in the same hand for a given door.

Leaf thickness is 0.092 inches in steel. That is a residential gauge, adequate for a standard fiberglass entry slab, but if you are hanging a heavy insulated or glazed door on three hinges, step up to a heavy weight commercial hinge rather than pushing this one.

For a straightforward residential exterior opening, the Delaney RH45xx 4 x 4 exterior residential hinge with 5/8 inch radius corners covers the same size class and also sells by the pair. For interior doors at a smaller size, the Delaney RH35xx 3-1/2 x 3-1/2 bulk hinge or the Emtek 91013 residential plain bearing pair with square corners are the usual choices. None of those carry the security tab or the wider 4-1/4 inch throw, so if you bought this hinge for clearance over brickmould, they will not solve that.

Several full mortise steel hinges in the same family serve entirely different functions. The Command Access ETH-CB70 and ETH-BB68 are energy transfer hinges that pass power through the hinge to an electrified lock, and the ETM-BB68 and ETM-CB70 add door position sensing. The BEST CECB179-12C is an electrified concealed bearing hinge with a 12-wire quick connect and the Stanley CECB1900R54L is a 4-wire concealed conductor hinge. The Stanley 2060R is a spring hinge that self-closes the door, and the BEST DAP-3 is a double acting pivot rather than a butt hinge. The Deltana S41/4058R-S is a plain mechanical butt hinge with no electrical path and no closing spring.

The S41/4058R-S uses a plain bearing, which suits residential-weight fiberglass entry doors. For heavier leaves or higher cycle counts, the Don-Jo HWBB84545 is a heavy weight full mortise ball bearing hinge at 4-1/2 inch by 4-1/2 inch and the Don-Jo HWBB75045 is heavy weight ball bearing at 5 inch by 4-1/2 inch. The Orca 3535 Series is a 4-1/2 by 4-1/2 square corner ball bearing commercial hinge at medium duty. All three run larger leaves than the Deltana, so the door and jamb mortises have to be cut or shimmed to match.

Only if the opening is prepped for a 3-1/2 inch leaf. The Emtek 91013 is a residential plain bearing pair at 3-1/2 by 3-1/2 with square corners and the Emtek 92013 is a heavy duty plain bearing pair at the same 3-1/2 by 3-1/2 with square corners, both plated steel. The Deltana S41/4058R-S is 4 inch by 4-1/4 inch with 5/8 inch radius by square corners, so neither Emtek fills a mortise cut for the Deltana, and neither carries the security stud the Deltana includes.

Yes. The Deltana S41/4058R-S is supplied as a left hand or right hand pair in zinc dichromate, so the swing has to be confirmed before ordering. Among the alternatives, the Stanley CECB1900R54L is also specified left-handed. Symmetrical butt hinges such as the Orca 4040 Series 4 by 4 square corner plain bearing hinge and the Delaney CH401X 4 by 4 commercial ball bearing square corner hinge are not handed, which is worth knowing if you are stocking one part number across a building.

The Deltana S41/4058R-S is classed residential. Where the drawing calls for a commercial standard weight 5-knuckle hinge, the McKinney MP79 and MPB79 MacPro hinges are 5-knuckle full mortise at standard duty, and the Stanley FBB191 is a 5-knuckle full mortise standard weight hinge in 4.5 by 4.5. McKinney T2314 is a non-ferrous 5-knuckle standard weight option at medium duty where a corrosion-resistant base metal is required.

The Deltana S41/4058R-S mounts full mortise, with both leaves let into the door and the jamb. If the frame cannot be mortised, the Hager 1129 is a half mortise plain bearing commercial hinge in 4-1/2 inch standard weight steel, and the Hager 990 STEEL is a full surface prison hinge, 3 inch by 4 inch with a welded tip, that screws to the face of the door and frame. Both change the prep entirely rather than dropping into a mortised opening.

Zinc dichromate, in both the left hand and right hand versions. That is a plated utility finish, so it is the right pick when the hinge is hidden behind a screen or storm door, or when the opening is being painted out. It is not a decorative finish, so if the hinges will be visible on a finished entry you are matching hardware on, plan accordingly.

The Deltana S41/4058R-S runs 5/8 inch radius by square corners, so one leaf is radiused. For an opening machined fully square, the Orca 4040 Series is a 4 inch by 4 inch square corner plain bearing commercial hinge at medium duty, and the Orca 3514 and 4014 Series use a 1/4 inch radius corner in 3-1/2 and 4 inch sizes if the existing mortise has a tighter radius. The Ives 3CB1 is a 3-knuckle full mortise hinge with concealed bearing rather than plain bearing, which changes the knuckle appearance at the barrel.