Deltana SAHF358 Floor Mount Door Bumper with Holder, Solid Brass

A fixed height floor bumper only works if the riser matches the undercut at the door. Where door to floor clearance varies across a building, the Ives FS40 / FS41 / FS42 / FS43 automatic floor stop and holder is built for adjustable door-to-floor clearance, and Ives also lists the FS18S and FS18L as short and long versions of the same security floor stop. Measure the clearance at the stop location before committing to a single fixed height unit.

No. A mechanical floor holder like the SAHF358 keeps the door open until someone releases it by hand, which is not what a fire rated opening needs. For a hold open that releases, look at a magnetic holder such as the SOSS MDH magnetic door holder and stop, measuring 3-5/16 by 1-3/4 inches. Use the SAHF358 on non rated doors, offices, and entries where a manual hold open is what you want.

The Deltana SAHF358 is a floor mount door bumper with holder in solid brass, so the door catches and stays put rather than just stopping. Two comparable holders cover the same job: the Orca Hardware 22HD Series goose neck floor stop, which lists a door holder function, and the Ives FS40 / FS41 / FS42 / FS43 automatic floor stop and holder, which offers adjustable door-to-floor clearance. The Orca 22HD is a goose neck profile that rises off the floor to meet the door edge; the Ives FS40 family is a heavy duty automatic holder set. All three combine stop and hold in one floor mounted unit.

Reach for a goose neck or an adjustable-clearance stop. The Orca Hardware 22HD Series goose neck floor stop lists a door thickness range of 1-3/8 inch or 1-3/4 inch and a door holder function, so it both meets a raised door edge and holds. The Emtek 2253 Goose Style Door Stop and the Delaney Gooseneck Floor Door Stop use the same raised neck geometry without the holder. The Ives FS40 / FS41 / FS42 / FS43 set is specified with adjustable door-to-floor clearance, which is the direct answer when the gap under the door varies across a building.

No. The Emtek 2251 Half Dome Door Stop, the Emtek 2257 1-1/2 inch cylindrical floor bumper, and the Delaney Dome Door Stop are stop-only floor units that arrest the door swing. The Deltana SAHF358 is a floor mount door bumper with holder, so it keeps the door open once caught. Swapping a dome stop onto an opening that was relying on the hold-open leaves the door free to swing back. For a like-for-like on that opening, stay with a holder such as the Orca 22HD Series, which lists a door holder function.

Ten finishes, and it matters if you are matching hinges and levers across a building: PVD Polished Brass, Polished Brass, Unlacquered Brass, Antique Brass, Oil Rubbed Bronze, Brushed Nickel, Antique Nickel, Polished Chrome, Brushed Chrome, and Paint Black. PVD Polished Brass is the one to specify if you want the brass look without the ongoing polishing; Unlacquered Brass will patina on purpose.

Mounting hardware is in the bag. Each SAHF358 ships individually poly bagged with its mounting hardware included, sold one per unit, so nothing extra is needed to fasten it down. What the hardware supplied will not cover is a concrete or tile floor, where you supply the appropriate anchors for that substrate.

A floor mounted stop like the Deltana SAHF358 is the choice when the door swings into open space with no wall behind it at handle height, or when the wall is glass or drywall that will not take the impact. It does mean drilling the finish floor, so it is a poor fit over radiant heat or a floor you cannot penetrate. The SAHF358 mounts to the floor only; there is no wall mount version of it.

Gooseneck stops rise on a curved post to meet the door higher up, which suits doors with a big floor gap or where you want the contact point away from the door bottom rail. Options we carry include the Delaney Gooseneck Floor Door Stop, the Emtek 2253 Goose Style, and the Orca 22HD gooseneck with black tip. A low profile floor bumper such as the SAHF358 or the Orca 23LP low rise dome sits close to the floor, which is less of a trip hazard in a corridor but needs a smaller door undercut to make contact.

Low-rise and small-footprint stops are the ones to look at. The Orca Hardware 23LP Series is a dome floor stop, low rise, with a gray tip and a door stop function. The Emtek 2254 Floor Door Bumper is 1-3/8 inch by 1-1/4 inch, and the Emtek 2257 is a 1-1/2 inch cylindrical floor bumper. The Emtek 2251 Half Dome and Delaney Dome Door Stop are the other dome profiles. The Deltana SAHF358 stands taller because it carries the hold-open function, so pair the low-rise stops with it only on the doors that do not need to be propped.

The Deltana SAHF358 is a solid brass floor mounted bumper with holder specified for commercial use. On the heavy duty side, Ives lists the FS13 heavy duty brass floor dome stop with a replaceable rubber bumper and the FS17 heavy duty brass floor dome stop with rubber bumper, both brass like the Deltana. The FS13 calls out a replaceable bumper, so the rubber can be renewed in place rather than swapping the whole stop. The Ives FS18S/FS18L security floor stop is also heavy duty. Those Ives units are dome and security stop styles rather than bumper-with-holder.

They solve overlapping problems by different means. The SOSS MDH is a heavy duty magnetic door holder and stop measuring 3-5/16 inch by 1-3/4 inch, and it uses a magnet plus a strike plate on the door to catch and hold. The Deltana SAHF358 is a mechanical floor mount bumper with holder in solid brass, so nothing has to be fastened to the door face. Choose the MDH when a magnetic catch is wanted and the door can take a strike; choose the SAHF358 when the hardware should stay entirely at the floor.

The Deltana SAHF358 is solid brass and comes in finishes including PVD Polished Brass, Polished Brass, Unlacquered Brass, Antique Brass, Oil Rubbed Bronze, Brushed Nickel, Antique Nickel, Polished Chrome, Brushed Chrome, and Paint Black. Among the comparables, the Ives FS13 and Ives FS17 are both heavy duty brass floor dome stops. The Deltana carries the broader finish range and the hold-open function; the Ives dome stops are stop-only brass units.

The SAHF358 is solid brass through the body, not brass plated, so surface wear does not expose a dissimilar base metal. In wet or chlorinated air, the finish choice does most of the work: Unlacquered Brass will darken and patina, and lacquered or plated finishes such as Polished Chrome or Brushed Chrome hold their appearance better in damp rooms.

Deltana floor mounted bumpers come in several sizes and designs, and the same finish range runs across them, so a property manager standardizing on Oil Rubbed Bronze or Brushed Nickel can keep one finish while varying the bumper profile by opening. The SAHF358 is the floor mount bumper with holder in that family.

The Orca Hardware 22HD Series is a goose neck floor stop with a black tip and a door holder function, and it lists a door thickness range of 1-3/8 inch or 1-3/4 inch. The Orca Hardware 23LP Series is a low rise dome floor stop with a gray tip and a door stop function only. The Deltana SAHF358 is a solid brass floor mount bumper with holder, which puts it alongside the 22HD on function and against the 23LP on profile.