Deltana SSPBB1210 12" Contemporary Pulls, Back-to-Back

Back-to-back means a matched pair, one pull on each face of the door, bolted through to each other rather than surface-screwed. The SSPBB1210 ships that way as a set with the mounting hardware, so a single order covers both sides of the opening. Note the unit of measure is each and the price shown is per unit.

Both. The Deltana Contemporary stainless pull kits include the installation hardware required for glass and wood doors, so you are not sourcing separate glass fasteners. The through-bolt setup covers doors 1-3/8 to 1-7/8 inches thick, which is where tempered glass entry leaves and standard wood leaves both fall.

No - they solve different halves of the opening. The Trimco 1070 series is a classic push/pull plate at 3-1/2 by 15 inches, a flat plate applied to the door face, and the Trimco 1001-1 is a heavy duty push plate at 3 by 12 inches with no grip at all. The Deltana SSPBB1210 is a 12 inch stainless steel pull handle with a 1 inch section, mounted back-to-back so there is a graspable handle on both faces. If the pair of doors needs push on one side and pull on the other, the plates are the right family; if both sides need something to pull on, the SSPBB1210 is.

The Ives 8103HD is the nearest peer: a heavy duty straight door pull in 1 inch round bar with through bolt mounting. The SSPBB1210 is a 12 inch stainless steel contemporary pull in a back-to-back configuration with 1 inch thickness, fitting doors 1-3/8 to 1-7/8 inch thick, and its kits include the mounting hardware for glass and wood doors. Both give a straight round-section grip at 1 inch; the Ives is specified as a heavy duty through-bolted pull, while the Deltana ships as a matched back-to-back pair.

Go to an offset pull. The Ives 8145 is a 45 degree offset door pull with heavy duty mounting hardware in the ADA compliant EZ series, and the Ives 8169 is a C style offset solid pull at 1 inch diameter with heavy duty mounting. The Deltana SSPBB1210 is a straight 12 inch contemporary pull mounted back-to-back, so its grip runs parallel to the door face and gives only the clearance the 1 inch standoff thickness provides. An offset pull angles the grip away from the door leaf for hand clearance in a confined opening.

The SSPBB1210 has a 1 inch thickness on the pull body, with a 12 inch overall length. That 1 inch bar is the same nominal size as the ABH AB3300 straight flat end pull and the Ives 8103HD, so if you are matching hand feel across a building, the grip diameter lines up with those.

Three: Paint Black, Polished Stainless, and Brushed Stainless. All three are on the same stainless steel body, so on a storefront or lobby entry you can pick brushed to match existing satin stainless hardware, polished for a bright match, or paint black when the frame is dark anodized or painted.

The SSPBB1210 is classified commercial. It is solid stainless steel through and through, and the back-to-back through-bolt mounting is what makes it hold up in traffic, the load goes into the fasteners spanning the door rather than into screws biting a single face. That is the same mounting principle as the heavy duty Ives 8103HD through-bolt pull.

Yes. Deltana Contemporary stainless pulls run in three lengths, and the SSPBB1210 is the 12 inch. If a 12 inch grip is too short for a tall glass entry leaf or too long for a narrow stile, look to the other lengths in the same series so the finish and the 1 inch bar profile stay consistent across the openings.

The SSPBB1210 is a straight bar pull, so if your opening needs the hand clearance of an offset, it is the wrong shape. ZenSupply carries the ABH AB3310 offset flat end pull and the ABH AB3330 offset round end pull, plus the Ives 8145 45 degree offset, which is listed as ADA compliant, and the Ives 8169 C style offset in a 1 inch diameter to match this grip size.

The ABH AB7200 is a solid stainless steel flat end pull handle at 7/8 inch diameter with through-bolt mounting, a slightly finer section than the 1 inch thickness of the Deltana SSPBB1210. The ABH AB3300 is a straight flat end commercial door pull at 1.00 inch diameter, matching the Deltana's section. Both ABH pulls are flat end straight profiles; the SSPBB1210 is a 12 inch contemporary stainless pull supplied back-to-back with the hardware for glass and wood doors included.

No. The Cal-Royal PUL-175 is a night latch cylinder pull, 3-1/2 inches high in stainless steel construction - it mounts around a rim cylinder on the exterior of a night latch door and gives a short finger pull. The Deltana SSPBB1210 is a 12 inch stainless steel pull with a 1 inch section, mounted back-to-back for a full-hand grip on both faces of a door 1-3/8 to 1-7/8 inch thick. If the door has a rim cylinder needing a trim pull, the Cal-Royal is the part; for a general commercial entrance grip, it is not a substitute.

The ABH AB3330 series is an offset round end pull offered with custom length options, and the ABH AB3310 is an offset flat end commercial grade surface mount pull. The Deltana SSPBB1210 is a fixed 12 inch stainless steel pull, part of a contemporary stainless range built in three lengths, with kits that include the hardware required for glass and wood doors. Where a drawing calls a length outside the standard range, the AB3330 is the series that takes a custom call-out; note the ABH offsets are surface mount rather than a back-to-back pair.

The Trimco 1035 Ultimate Restroom Pull is the purpose-built option for that opening and is rated heavy duty. The Ives 8102HD is another heavy duty choice, a straight pull on 3/4 inch round bar with 1-1/2 inch clearance. The Deltana SSPBB1210 is a 12 inch stainless steel contemporary pull with a 1 inch section, mounted back-to-back so both faces of the door carry a handle - a fit where the design intent is a matched pull on each side rather than a restroom-specific device.

The Ives 8145 is called out as an ADA compliant pull in the EZ series, a 45 degree offset with heavy duty mounting hardware, so where the drawing names ADA compliance explicitly that is the part to price. The Deltana SSPBB1210 is a 12 inch stainless steel back-to-back pull with a 1 inch grip section for doors 1-3/8 to 1-7/8 inch thick, specified as commercial.

No handing to specify. The SSPBB1210 is a symmetrical straight bar pulling the same on either leaf, so one part number covers left hand and right hand openings and both leaves of a pair. That is a difference from styled pulls like the Emtek Art Nouveau, which is ordered by handing.

Stainless steel is both the material and the substrate on the SSPBB1210, so the brushed and polished finishes are the metal itself rather than a plating over a different base. For exterior entries and coastal or wash-down interiors, that matters more than the finish name does.