Emtek 2260 Cylinder Floor Bumper with Dome Cap, 2"

Emtek lists the 2260 as residential. It's solid brass and it will do its job behind a bedroom, bath, or entry door in a house or a unit interior, but for a high-traffic commercial opening the heavy duty options are the right call: the Ives FS13 and FS17 brass floor dome stops are both listed heavy duty, and the FS13 uses a replaceable rubber bumper so the wear part can be swapped instead of replacing the stop. Property managers standardizing across a building with real door traffic should be shopping that tier.

The 2260 measures 2 inches. Because it stands off the floor rather than sitting low, it catches the door face rather than the bottom rail on most openings, but you need floor-to-door-bottom clearance under 2 inches for the door to pass over it before it makes contact. If your door has a big undercut over carpet, a low rise stop like the Orca Hardware 23LP Series dome floor stop is the shape that suits that condition better.

The dome cap floor stop is a common shape, so there are direct equivalents. Delaney's Dome Door Stop is the same basic type. In solid brass, Deltana's UFB Series UFB4505 is a 1-1/2 inch round universal floor bumper and the UFBP4505 is 1-5/8 inch with a pattern cap. If you want a taller stop than the 2260's 2 inches, the Deltana UFBD3505 is 3-1/2 inch decorative. And if you want to break from the round shape entirely, the Deltana UFBS138 is a 1-3/8 inch square in solid brass.

A cylinder floor bumper like the Emtek 2260 arrests the door swing only; it does not hold the door open. For hold-open, the Ives FS40 / FS41 / FS42 / FS43 Automatic Floor Stop and Holder is a heavy-duty stop and holder with adjustable door-to-floor clearance, and the SOSS MDH Magnetic Door Holder and Stop, at 3-5/16 inch by 1-3/4 inch, is a heavy-duty magnetic holder that also serves as the stop. Orca Hardware's 22HD Series goose neck floor stop is catalogued with a door holder function for openings that suit a goose neck body. Choose the holder style by how the door is used, not by the stop profile.

The Emtek 2260 is a 2-inch cylinder floor bumper with a dome cap in brass. The nearest same-shape peers are the Deltana UFBD3505 Round Universal Floor Bumper, a decorative 3-1/2 inch solid brass floor bumper, and the Deltana UFB4505 Round Universal Floor Door Bumper at 1-1/2 inch in solid brass. The Delaney Dome Door Stop is another dome-profile floor stop. All three are round-body floor-mounted stops in the same family as the 2260; the difference is body height, so measure the gap between your door and the wall or fixture you are protecting and pick the projection that closes it.

The Emtek 2260 is specified for residential use. For openings in commercial traffic, the Ives FS13 Heavy-Duty Brass Floor Dome Stop with Replaceable Rubber Bumper and the Ives FS17 Heavy-Duty Brass Floor Dome Stop with Rubber Bumper are both heavy-duty brass floor dome stops in the same mounting style. The FS13 carries a replaceable rubber bumper, so a facility standardizing across many doors can renew the strike surface without pulling the base off the floor. Ives also lists the FS18S/FS18L Security Floor Stop as a heavy-duty option where the stop needs to resist tampering.

The Emtek 2260 is a 2-inch cylinder bumper, so it reaches the door face only where the leaf runs close to the floor. Where the reveal is larger, a goose neck stop puts the strike point up on the door rather than at floor level: the Orca Hardware 22HD Series Goose Neck Floor Stop with black tip is listed for 1-3/8 inch or 1-3/4 inch doors, and the Delaney Gooseneck Floor Door Stop is the same body style. Going the other direction, for a shallow reveal Orca lists the 23LP Series Dome Floor Stop as a low-rise dome stop with a gray tip. Measure from the finished floor to the point on the door you want contacted before you pick.

Screws are included with the 2260. What's not included is anything for the substrate you're going into: the supplied screws suit a wood subfloor, so on concrete or tile you'll want your own anchors and a masonry bit. That's the only extra piece to plan for on the install.

Five: Oil Rubbed Bronze (US10B), Satin Nickel (US15), Flat Black (US19), Polished Chrome (US26), and Unlacquered Brass (US3NL). That spread is chosen to match Emtek's knob, lever, and hinge finishes, so if you're finishing out a room you can carry the same US code across the door hardware and the stop. The Unlacquered Brass is a living finish and will darken with handling and time, which matters if you're trying to match an existing bright brass door set exactly.

Brass through the body, not a plating over zinc. Emtek lists both the material and the substrate as brass, and it sits in their Brass collection. That matters where the stop takes a repeated strike or where a screwdriver ends up prying at it during a floor refinish.

Two different geometries for two different door swings. The 2260 is a straight 2 inch cylinder rising off the floor, so the door face hits the dome cap directly, and it sets close to the door's arc. A goose neck arcs up and back to meet the door higher, which suits an opening where the stop has to sit further out from the door or where you want contact above the bottom rail. Delaney's Gooseneck Floor Door Stop and Orca's 22HD Series are the goose neck shape if that's the condition you have.

No. The 2260 is a residential brass cylinder stop, fine for a homeowner's door but not built for abuse or tampering. For a rental corridor or anywhere the stop gets kicked, the Ives FS18S / FS18L security floor stop is the heavy duty part designed for that condition.

They differ in the cap the eye sees. The Emtek 2260 carries a plain dome cap on a 2-inch cylinder body in brass, in the American Classic style. Deltana's UFBP4505 is a round universal floor door bumper with a pattern cap at 1-5/8 inch in solid brass, so the top face is decorated rather than smooth, and the UFBS138 is a square universal floor door bumper at 1-3/8 inch in solid brass, with a squared body instead of a round one. For a designer matching an existing suite of trim, the cap treatment and body geometry are the deciding detail; all three mount to the floor the same way.

For plain replacement work where the finish does not need to match a decorative suite, the Delaney Dome Door Stop and the Delaney Gooseneck Floor Door Stop cover the same job in the two common body styles - dome for a door that swings close to the floor, goose neck for one that does not. The Emtek 2260 is a 2-inch brass cylinder in the American Classic style and includes its screws, which is what you want when the stop is visible in a finished space. On a fleet of units, pick one body style and stay with it so a maintenance tech carries a single part.

Not as a like-for-like swap. The SOSS MDH Magnetic Door Holder and Stop measures 3-5/16 inch by 1-3/4 inch and is a heavy-duty holder that catches and retains the door magnetically, which means it needs a mating catch plate on the door and a defined open position. The Emtek 2260 is a 2-inch cylinder bumper that simply arrests the swing wherever it is set, with no catch and nothing mounted on the door leaf. If the door only needs its travel limited, the 2260 stays the simpler install; if it needs to be parked open, the MDH is the correct part.

The Ives FS13 Heavy-Duty Brass Floor Dome Stop is listed with a replaceable rubber bumper, so the strike surface is a serviceable part. The Ives FS17 is the heavy-duty brass floor dome stop with a rubber bumper, and Orca's 22HD Series goose neck carries a black tip while the 23LP Series low-rise dome carries a gray tip. The Emtek 2260 is a 2-inch brass cylinder bumper with a dome cap. On a facility where stops take repeated contact, the serviceable-tip route keeps the base and finish in place through the life of the door.

No. The Ives FS18S/FS18L Security Floor Stop is a heavy-duty floor stop built for openings where the stop itself may be attacked or defeated, which is why an integrator specifies it on a secured door. The Emtek 2260 is a 2-inch brass cylinder floor bumper with a dome cap intended for residential use; it protects the wall and limits door travel. If the door is on a secured opening, the FS18S/FS18L is the part that belongs there and the 2260 is not a substitute for it.

Three round brass bumpers sit below the Emtek 2260's 2-inch body. Deltana's UFB4505 Round Universal Floor Door Bumper is 1-1/2 inch in solid brass, the UFBP4505 pattern cap version is 1-5/8 inch in solid brass, and the square-bodied UFBS138 is 1-3/8 inch in solid brass. Orca's 23LP Series Dome Floor Stop is described as low rise. A shorter body contacts the door lower on the leaf, so confirm the door bottom clears the cap before committing.

It's built to. The 2260 is part of Emtek's American Classic styling and comes in the same US finish codes used across their knobsets and leversets (US10B, US15, US19, US26, US3NL), so ordering the stop in the same code as the door set gives you a match. Order the 2260 in the same finish code as the lever or knob on that door and the stop won't read as an afterthought.