Emtek 7370 Missoula 3-5/8" C-to-C Keyed Sideplate Lockset, Passage/Single Keyed - Sandcast Bronze Tubular

Both. The Missoula 7370 covers 1-3/8 inch through 1-3/4 inch doors, which takes in standard commercial-weight residential entry doors at 1-3/4 and older interior slabs at 1-3/8. Door thickness is one of the things you specify when ordering, so give the actual slab measurement rather than assuming.

It uses one standard 2-1/8 inch cross bore, so a door already bored for a normal tubular knob or lever set takes it without a new bore. What it does add is the sideplate: the trim is a long plate rather than a round rose, so the face of the door needs to be clear where that plate lands, and the plate has a 3-5/8 inch center-to-center spacing between the bore and the keyed cylinder. Backset is 2-3/8 or 2-3/4 inch, so it can be matched to whatever the existing bore is set at.

Two backsets are offered, 2-3/8 inch and 2-3/4 inch, and backset is a required selection on the order. Measure from the edge of the door to the center of the bore: those two are the only backsets in normal residential use, so it will be one or the other. The standard latch ships 2-3/8 inch, so call out 2-3/4 explicitly if that is what the door is bored for.

Yes, and it is not optional on a lever. Handing is a required choice, right hand or left hand, because the lever has to point toward the latch edge and cannot be flipped in the field. Stand outside the door: if the hinges are on your right it is right hand, hinges on your left is left hand. Get it backwards and the lever points the wrong way.

Keying is a required choice on the order and both keyed alike and keyed different are offered, at no charge. Keyed alike puts one key across every set on the order, which is what you want for a front, side and back door on the same house. There is also a keying to code field if you are matching an existing key code already in the building.

Residential. The Missoula 7370 is a sandcast bronze tubular entry set built for houses, and that is how it should be specified. For a leased commercial entry, a school corridor, or anything on a scheduled opening, a bored lock built for that traffic is the right call instead.

The Emtek 7370 Missoula sideplate lockset is a single cylinder entry function, keyed on the outside with a thumbturn or inside trim only. For an opening that needs a key on both sides - a door with glass beside it, or an exit you want to control from the inside - the Omnia D12036AC is a double cylinder deadbolt lever lockset with a sideplate design in solid brass. Both are sideplate lever sets; the difference is where the cylinder sits. Local code on egress doors governs whether double cylinder is permitted.

The Emtek 7370 Missoula is a keyed entry lockset, so it is the wrong part for a closet, pantry, or a false active leaf on a pair. The Omnia D12036PD is a double dummy deadbolt lever lockset with plates, 5-1/2 inch center to center, in solid brass - surface mounted trim with no latch and no cylinder. Note the center-to-center difference: the Emtek 7370 Missoula is 3-5/8 inch, so the two will not read as the same plate spacing side by side on adjacent doors.

It ships as a complete set: the sideplate with the knob or lever you select, the latch, and the strike plate. Because it is a single cylinder entry, the outside takes the key and the inside trim operates by hand. You pick the inside knob or lever style separately, and the latch faceplate is available in round corner or square corner to match the existing mortise in the door edge.

Yes. The inside trim is a required selection and the Sandcast Bronze range covers both. Knobs include Butte, Egg, Round, Winchester, Bristol, Hampton, Lowell, Windsor, Astoria, Diamond, Georgetown, Modern Disc, Modern Square, Old Town and Providence. Levers include Aurora, Bryce, Cimarron, Cody, Durango, Lariat, Mariposa, Montrose, Teton and Yuma. Any Sandcast Bronze knob or lever style can be ordered on it.

Three, all Sandcast Bronze: Flat Black Bronze (FB), Medium Bronze (MB) and Tumbled White Bronze (TWB). These are living bronze finishes, not plated, so they are meant to darken and wear in over time rather than stay uniform. If you are matching hardware already hanging in the building, match to the Sandcast Bronze code and not to a plated equivalent.

A sideplate set puts the key cylinder and the knob or lever on one continuous plate, 3-5/8 inch center to center, so the whole assembly reads as one piece of hardware on the door face instead of two. It still needs only one 2-1/8 inch bore. A separate lockset and deadbolt gives you two independent bores and a true deadbolt throw; the sideplate set is the choice when you want the long-plate look and a single prep. If you specifically want the deadbolt style on a plate, Omnia builds that as the D12036A single cylinder deadbolt lever lockset.

Functionally they line up: the Omnia D12036A is a single cylinder deadbolt lever lockset in solid brass, and the Emtek 7370 Missoula is a single cylinder keyed entry sideplate lockset. Where they part company is material and center-to-center. The Emtek 7370 Missoula is sandcast bronze on a 3-5/8 inch center-to-center plate; the Omnia is solid brass. If you are matching an existing sandcast bronze suite on the other doors, the Emtek stays in the family. If the door prep or the plate spacing is the deciding factor, confirm the center-to-center before swapping either way.

No. The Omnia D12036PD is a double dummy - lever plates with no latch and no cylinder, so it does not latch or lock. The Emtek 7370 Missoula is a keyed single cylinder entry lockset in tubular format with an adjustable 2-3/8 or 2-3/4 inch backset latch and strike plate included. The two look similar on the door because both are sideplate levers, which is exactly why they get confused. For an entry opening you need the keyed set; the dummy belongs on the inactive or non-latching leaf.

Purely mechanical. It is a keyed tubular entry lock, no electronics, no wiring, no batteries. If the job calls for keypad or app access, this is not that part.