Emtek 8405 Select Cabinet Pulls, Schaub Collection

The 8405 Select bar pull is made in ten center-to-center spacings: 3-1/2, 4, 5, 6, 8, 10, 12, 16, 20 and 24 inches. That range covers drawer fronts and full-height appliance and pantry doors from one family, so a kitchen can run the small sizes on drawers and the 16 to 24 inch bars on the refrigerator and freezer panels with the same bar and finish. Order by the hole spacing already drilled in the front, not by the overall bar length.

No. On the 8405 Select pull the stem and bar are permanently affixed, so what you pick at order time is what you get for the life of the part. It ships as a complete set with mounting screws included. Decide the bar style, stem, finish and center-to-center before you order, because none of it comes apart afterward for a swap.

Four choices build an 8405: bar pull style, either Knurled (KN) or Smooth (SM); the stem, which is Rectangular (REC); the center-to-center, from 3-1/2 up to 24 inches; and the finish. There is also a stem finish field, so the stem can be called out separately from the bar if you want the two to differ. Miss one and the order cannot be built.

Not directly. The 8405 Select bar pull starts at 3-1/2 inches center-to-center, so a front drilled at 3 inches needs new holes or a different pull. Schaub's 10010 Sabre edge pull is a 3 inch center-to-center part, and Trimco's 553 Series drawer pull is 3 inch ctc, if you would rather keep the existing bores than redrill.

Yes, the long sizes are made for it. The 8405 Select bar pull runs to 16, 20 and 24 inch center-to-center, the spacings used on integrated refrigerator, freezer and pantry panels, and it uses the same brass bar and finish as the shorter drawer sizes so the whole run matches. Confirm the spacing already drilled in the appliance panel before choosing the size, since the stem and bar are permanently affixed and cannot be adjusted after.

The Omnia 1968/102 is a modern cabinet pull in forged solid brass with 4 inch center-to-center spacing, which is the same drilling as the 4 inch Emtek 8405 Select. Both are brass. Where they part company is the styling program: the 8405 is a stem-and-bar pull on a rectangular stem, offered with a knurled or smooth bar, so the texture choice is part of the order. If you want the knurled bar face on the drawer, the 8405 is the one that offers it at 4 inch.

The Deltana SBP35 Modern Square Bar Pull is the nearest match: a heavy-duty solid brass square bar pull at 3-1/2 inch center-to-center. The Emtek 8405 Select cabinet pull is brass and includes 3-1/2 inch in its center-to-center range, so the two line up at that one drawer size. The difference is range: the 8405 runs from 3-1/2 inch up through 4, 5, 6, 8, 10, 12, 16, 20 and 24 inch, so if a kitchen mixes small drawers with tall pantry and appliance fronts, the 8405 carries the whole run in one look while the SBP35 covers the 3-1/2 inch size.

When knuckle clearance off the face is the deciding dimension, the Omnia pulls state their projection where the Emtek 8405 Select does not commit you to one: the Omnia 1969 and Omnia 1971 are forged solid brass modern cabinet pulls at 1-3/16 inch projection, and the Omnia 1970 is the same construction at 1-1/4 inch. If the opening has a hard clearance number to hit, specify from those. If clearance is not the constraint, the 8405 gives you the wider size ladder and the knurled or smooth bar choice.

No - they mount differently and are not interchangeable. The Schaub 10010, 10011 and 10012 Sabre pulls are edge pulls, in 3 inch, 4 inch and 5 inch center-to-center respectively, which mount on the edge or reveal of the door or drawer. The Emtek 8405 Select is a face-mounted stem and bar cabinet pull, sold as a complete set with screws, with the bar permanently affixed to the stems. If the design calls for hardware that sits on the door face, the edge pulls will not substitute for it, and vice versa - the boring is not the same job.

Seven finishes on the 8405 Select pull: Flat Black (US19), Oil Rubbed Bronze (US10B), Polished Chrome (US26), Polished Nickel (US14), Satin Brass (US4), Satin Copper (SCU) and Satin Nickel (US15). Five of those carry standard US finish codes, so US26 chrome or US15 satin nickel here lines up with the same code on door hardware elsewhere in the house. Satin Copper is Emtek's own designation rather than a US number.

Brass, both the material and the substrate on the 8405 Select pull, so the finish sits on brass rather than on plated steel or zinc. That matters on a knurled bar that gets gripped every day, and it is why the finish list runs to living finishes like Satin Brass and Satin Copper. Among comparables, Deltana's SBP35 square bar pull and Omnia's 1968, 1969, 1970 and 1971 pulls are also solid brass, the Omnias forged.

The 8405 comes both ways, Knurled (KN) and Smooth (SM), and it is a grip and cleaning decision. Knurled gives texture under wet or greasy hands, which is why it turns up on ranges and sink runs, but the pattern holds fingerprints and needs wiping into the grooves. Smooth wipes clean in one pass and reads quieter on a long 20 or 24 inch appliance bar. Both use the same rectangular stem, so you can mix styles across one kitchen and keep the projection and finish consistent.

Emtek lists the 8405 Select pull as residential. It is built for kitchens, baths and millwork in homes and residential units, not for the traffic of a commercial casework spec. If you are pulling drawer hardware for a commercial fit-out, Trimco's 553 Series and 562 Series drawer pulls are the institutional-side option ZenSupply carries, and Orca's CK-12001 T-pull bar is a steel bar pull in satin nickel.

No, the 8405 ships as a complete set with the screws included. One line item per pull covers what you need to hang it on a drilled front.

There is a separate stem finish option on the 8405, so the rectangular stem can be called out apart from the bar. That is how a two-tone pull is built, say a Flat Black (US19) bar on a Satin Brass (US4) stem. State the stem finish on the order; the assembly is permanent once made.

The 8405 is a two-hole bar pull, mounted on a rectangular stem at a set center-to-center spacing from 3-1/2 to 24 inches. A knob takes a single hole. If your fronts are drilled for one screw, a bar pull will not drop in, and something like Orca's Bachelor Collection round knob at 1-1/4 inch diameter or the Blackcomb square knob at 25mm is the single-bore part. Going the other way, moving from knobs to the 8405 means drilling a second hole in every front.

Two ways to go. The Emtek 8405 Select runs up to 8, 10, 12, 16, 20 and 24 inch center-to-center, so the appliance fronts can carry the same stem-and-bar pull in a longer size and the whole kitchen stays one family. If you would rather use a dedicated appliance pull, the Schaub 79-8 Steamworks 8 inch cabinet pull is built for that role. Matching within the 8405 range keeps the finish and the knurled or smooth bar consistent across cabinets and appliances; going to the Steamworks introduces a second design on the appliance doors deliberately.

They read similarly on a drawing but are not the same part. The Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width, made of steel, in satin nickel. The Emtek 8405 Select is brass, and its satin nickel is one of seven finishes alongside flat black, oil rubbed bronze, polished chrome, polished nickel, satin brass and satin copper. If the spec on the job calls for a brass pull, or the finish schedule is anything other than satin nickel, the CK-12001 will not answer it. If the run is short and satin nickel steel meets the spec, the Orca is a straightforward substitute.

The Emtek 8405 Select starts at 3-1/2 inch center-to-center, so for a front too narrow for that boring, go to a single-hole knob. The Orca Hardware CK-15030 is a round cabinet pull knob at 1-1/4 inch diameter, the CK-16030 is a round ring knob at the same 1-1/4 inch diameter, and the CK-17025 Blackcomb is a square knob at 25mm diameter. All three are single-bore, so they need one hole rather than a pair on 3-1/2 inch centers. A common approach is knobs on the narrow drawers and 8405 bar pulls on the wider ones.

The Trimco 553 Series drawer pull is a 3 inch center-to-center part, and the Trimco 562 Series comes in 3-1/2 inch, 4 inch and 96mm center-to-center options. If the existing holes in the units are on 3 inch centers, the Trimco 553 matches that boring and the Emtek 8405 Select does not, since its range starts at 3-1/2 inch. For units on 3-1/2 or 4 inch centers, either family drops into the existing holes. The Emtek 8405 is a residential-designated SELECT Series brass pull with seven finishes, so it is the choice when the turn is also a finish upgrade across the doors and drawers.

Contemporary is the style, and the 8405 belongs to Emtek's SELECT Series, the line built as a mix-and-match system where the bar and stem are chosen separately and then assembled as one permanent piece. That is what lets a single design carry across ten sizes and seven finishes on one job.

No. The SDC SP50 is a 50mm spindle, a door controls component. The Emtek 8405 Select is a cabinet pull with a rectangular stem and a bar permanently affixed to it, sold as a complete set with screws. The word stem on the 8405 refers to the post that carries the bar off the drawer face, not to a spindle that drives a latch. Nothing about the SP50 substitutes for the 8405.