Emtek Riviera Cabinet Pull, Schaub Collection

The Riviera pull is offered in 3-1/2, 4, 5, 6, 8, 10, and 12 inch center-to-center. That range covers a whole kitchen from one pull: 3-1/2 and 4 inch for drawer banks and small doors, 5 and 6 inch for standard base cabinets, and 8 through 12 inch for tall pantry doors and appliance panels. Measure hole spacing on your existing pull center of hole to center of hole and match it, and the new pull drops into the same two bores.

Only if your current hole spacing matches one of the sizes made: 3-1/2, 4, 5, 6, 8, 10, or 12 inches. The Riviera is a two-hole bar pull, so it mounts on the same pair of bores as the pull coming off, with no filling or re-drilling, provided the spacing lines up. If your existing pull is metric (96mm or 128mm, common on imported boxes) it will not line up with these, and you would be drilling new holes.

Yes, and that is the reason to pick the Riviera over a fixed-size pull. The same profile runs from 3-1/2 inches up to 12 inches center-to-center, so the drawer bank, the base doors, and the tall pantry all carry the identical design, just scaled. Standard practice is to step the length with the width of the front, longest on the appliance and pantry panels.

The closest cross-brand equivalent is the Omnia 1968/102, a forged solid brass modern cabinet pull at 4 inch center-to-center. Deltana's SBP35 is a solid brass square bar pull at 3-1/2 inch if you can shift the spacing. Trimco's 562 Series drawer pulls come in 3-1/2 inch, 4 inch, and 96mm, which is the one to reach for if the cabinet boxes are drilled metric. The Riviera differs from all of them in styling, it is a Hollywood Regency profile rather than a plain modern bar.

No. The smallest Riviera is 3-1/2 inch center-to-center, so a 3 inch bore pattern will not line up and you would be re-drilling every front. For an existing 3 inch pattern, the Trimco 553 Series drawer pull is made at 3 inch, and the Schaub 10010 Sabre is a 3 inch center-to-center edge pull if the mounting is on the door edge.

The Emtek Riviera cabinet pull is a brass cabinet pull offered in center to center spacings from 3-1/2 inch through 12 inch. For a 4 inch center to center in forged solid brass, the Omnia 1968/102 modern cabinet pull is built around that 4 inch spacing. The Riviera carries a Hollywood Regency style, while the Omnia 1968 series is a modern profile, so the two read differently on a door front even where the drilling matches.

The Deltana SBP35 modern square bar pull is a 3-1/2 inch heavy-duty solid brass pull with a square bar profile. The Emtek Riviera also comes in a 3-1/2 inch center to center in brass, but its styling is Hollywood Regency, so the Deltana is the one to specify when the cabinetry calls for a squared modern bar.

No. The Schaub 10010 is a Sabre edge pull at 3 inch center to center, and an edge pull mounts at the edge of a door or drawer face rather than sitting proud on the front the way a standard cabinet pull does. The Emtek Riviera is a cabinet pull. The Schaub 10011 and 10012 are the same Sabre edge pull in 4 inch and 5 inch center to center. Match the hole spacing all you like, the mounting condition is different.

The Emtek Riviera starts at 3-1/2 inch center to center, so a 3 inch drilling needs a different part. The Trimco 553 series drawer pull is a 3 inch center to center drawer pull. The Trimco 562 series covers 3-1/2 inch, 4 inch, and 96mm center to center, which overlaps the Riviera at 3-1/2 inch and 4 inch and gives a metric option the Riviera does not run.

Screws are included. Nothing else is needed to hang them on standard cabinet doors and drawer fronts. On unusually thick fronts or where a pull is going through a false drawer front plus a backing panel, you may need longer 8-32 machine screws than the ones supplied, since the screws that ship are sized for typical front thickness.

Six: Flat Black (US19), Oil Rubbed Bronze (US10B), Polished Chrome (US26), Polished Nickel (US14), Satin Brass (US4), and Satin Nickel (US15). Those US codes are the same finish designations Emtek uses on its door hardware, so if you are matching cabinet pulls to the levers and knobs already in the house, order by the US number rather than by the finish name and the two will read as one set.

The Riviera is a residential cabinet pull. For a multi-family unit turn, a model apartment, or an executive office millwork package it is the right kind of part. For a heavy-traffic commercial casework job, a hospital nurse station or a school casework run, look at something built for that duty instead, such as the Deltana SBP35 heavy-duty solid brass square bar pull.

Different jobs. The Riviera is a face-mounted cabinet pull in brass, ordered by center-to-center from 3-1/2 to 12 inches. The Schaub 10010, 10011, and 10012 Sabre pulls are edge pulls, meaning they mount on the edge of the door or drawer rather than the face, at 3, 4, and 5 inch center-to-center. The Schaub 79-8 Steamworks 8 inch is an appliance pull, sized and built for a refrigerator or dishwasher panel. If you want one look across a full kitchen, the Riviera does it; if you specifically need an edge-mount or a dedicated appliance pull, those Schaub parts are the ones.

The Emtek Riviera runs up to 12 inch center to center in brass. If the opening is a refrigerator or dishwasher panel, the Schaub 79-8 Steamworks 8 inch cabinet pull is built as an appliance pull, which is the category of pull intended for the loading an appliance door puts on the fasteners. The Riviera is a cabinet pull for residential cabinetry.

A knob takes one hole rather than the two-hole center to center drilling the Emtek Riviera uses. The Orca Hardware CK-15030 Bachelor Collection is a round cabinet knob at 1-1/4 inch diameter, the CK-16030 is the round ring version of the same knob at 1-1/4 inch diameter, and the CK-17025 Blackcomb Collection is a square cabinet knob at 25mm diameter. All three are cabinet knobs, so switching from the Riviera to any of them changes the door front prep.

Among the forged solid brass modern pulls, the Omnia 1969 and the Omnia 1971 both carry a 1-3/16 inch projection and the Omnia 1970 carries a 1-1/4 inch projection, so those three are the set to work from when a specific standoff has to clear a pilaster, an adjacent door swing, or a countertop overhang. The Emtek Riviera is a brass cabinet pull in the Hollywood Regency style covering 3-1/2 inch through 12 inch center to center.

Projection is the number that decides whether a pull clears an adjacent wall, an appliance handle, or a door swinging into it. For a comparison point on similar brass pulls, Omnia's 1969 and 1971 sit at 1-3/16 inch projection and the 1970 at 1-1/4 inch, so a bar pull of this class typically wants roughly an inch and a quarter of open space ahead of the face. In a tight inside corner or beside a fridge, check that gap before you commit to any face-mounted bar pull.

It is a two-hole cabinet pull, not a knob, so it mounts on a pair of bores and works equally on drawer fronts and cabinet doors. If part of the run needs knobs instead, single-hole options in the same category include the Orca Bachelor Collection round knob at 1-1/4 inch diameter and the Blackcomb square knob at 25mm.

Both are pulls, but they are different parts. The Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width in steel, finished satin nickel. The Emtek Riviera is a brass cabinet pull, and it offers satin nickel among its finishes, so the finish can match while the material and the bar geometry do not.

The Emtek Riviera cabinet pull is offered in Flat Black (US19), Oil Rubbed Bronze (US10B), Polished Chrome (US26), Polished Nickel (US14), Satin Brass (US4), and Satin Nickel (US15) across its 3-1/2 inch through 12 inch center to center range. Among the comparable brass pulls, the Deltana SBP35 is a heavy-duty solid brass square bar pull and the Omnia 1968, 1969, 1970, and 1971 are forged solid brass modern pulls, each built to its own single profile rather than the Riviera's Hollywood Regency styling.

No. The SDC SP50 is a 50mm spindle used in door control hardware, not cabinet hardware. The Emtek Riviera is a brass cabinet pull that mounts to a cabinet or drawer face with the mounting screws it ships with. There is no spindle in a cabinet pull assembly.