Emtek Trail Cabinet Pull, Schaub Collection

Yes. The Trail pull is made in 3 inch and 3-1/2 inch center-to-center, so it drops onto existing 3-1/2 inch drilling with no new holes. Larger sizes run 4, 5, 6, 8, 10, 12 and 16 inch center-to-center, which covers drawer banks and appliance fronts on the same design. Measure hole center to hole center, not the overall pull length, and order that number.

Projection is 1-7/8 inches on the Trail pull. That is what decides clearance in a galley kitchen or a hallway of built-ins, and it is also the number to check against a door swinging past an adjacent run. If you need something that sits tighter to the face, the Omnia 1969 and 1971 cabinet pulls carry a 1-3/16 inch projection and the Omnia 1970 a 1-1/4 inch.

The Deltana SBP35 Modern Square Bar Pull is a heavy-duty solid brass bar pull at 3-1/2 inch center to center, which is one of the center-to-center spacings the Trail pull is made in. The Trail is a brass cabinet pull in a contemporary style, so the two land in the same design family; the SBP35 carries a square bar profile, while the Trail is offered across a much wider spacing range from 3 inch up to 16 inch center to center. If a kitchen has drawers already drilled on 3-1/2 inch centers and only that one spacing is needed, the SBP35 covers it; if the same job also needs 10, 12, or 16 inch pulls for appliance-height drawers, the Trail run keeps one look across all of them.

Two things in the same aisle do not swap for it. The Schaub Sabre edge pulls -- 10010 at 3 inch, 10011 at 4 inch, and 10012 at 5 inch center to center -- match Trail spacings on paper, but they are edge pulls, mounted on the edge of a door or drawer rather than standing off the face like the Trail's 1-7/8 inch projection. Separately, the Orca Hardware CK-15030 and CK-16030 Bachelor Collection parts at 1-1/4 inch diameter and the CK-17025 Blackcomb square at 25mm are cabinet knobs, single-hole parts with no center-to-center dimension at all. If the drawer is already bored on two centers, only a two-hole pull will land on the existing holes.

Seven finishes: Flat Black (US19), Oil Rubbed Bronze (US10B), Polished Chrome (US26), Polished Nickel (US14), Satin Brass (US4), Satin Nickel (US15), and Unlacquered Brass (US3NL). For matching aged brass, Unlacquered Brass is the one that will patina over time rather than hold a fixed tone, so it darkens toward existing living-finish hardware. Satin Brass stays where it starts.

The Trail pull is a residential cabinet pull. For a single-family remodel, a model unit, or high-end multi-family casework it is a reasonable spec. For commercial casework where you need a listed grade or a project-standard pull, it is not the right line to standardize on, and a commercial bar pull such as the Trimco 553 or 562 Series drawer pulls fits that use better.

A pull like the Emtek Trail spans two holes and gives a full-hand grip, which is what you want on wide or heavy drawers where a single point makes the drawer rack in its slides. A knob is a single-hole install and works on small doors and narrow drawers. If you want knobs on the doors and pulls on the drawers, the Orca Hardware Bachelor Collection round knob at 1-1/4 inch diameter and the Blackcomb Collection square knob at 25mm are single-bore options.

Not in the Trail line, which projects 1-7/8 inches from the face. For a tight walkway or a door that has to sit flush, an edge pull is the type to look at: the Schaub Sabre edge pulls come in 3 inch (10010), 4 inch (10011) and 5 inch (10012) center-to-center and mount on the door edge instead of the face.

The Trail cabinet pull runs up to 16 inch center to center, which reaches appliance-panel length, and it is a cabinet pull rather than a part built specifically for appliance duty. The Schaub 79-8 Steamworks 8 inch cabinet pull is catalogued as an appliance pull, which is the purpose-built option for a refrigerator or range panel. Note that Trail is designated for residential use, so a commercial kitchen spec should be checked against that before the panel pulls are ordered.

The Orca Hardware CK-12001 T-Pull Bar is steel with a 2 inch bar width, supplied in satin nickel. The Trail is brass and comes in seven finishes including satin nickel, so the two can sit in the same satin nickel scheme with different base materials. Where a job is standardizing on brass throughout -- pulls, knobs, and door hardware in matching plating -- the Trail keeps the substrate consistent; where steel is acceptable and the design calls for a T-bar profile, the CK-12001 is the steel option.

At 3 inch center to center, the Trail pull is made in that spacing, and so is the Trail-adjacent set: the Trimco 553 Series drawer pull is a 3 inch center-to-center part, and the Trimco 562 Series covers 3-1/2 inch, 4 inch, and 96mm centers. For a property manager matching what is already bored into the drawer fronts across a building, 3 inch and 3-1/2 inch are the two spacings that come up most, and the Trail covers both in one finish family across seven finishes if the goal is a single look on every unit.

Contemporary. The Trail is a Schaub Collection design in a contemporary style, so it sits with flat-panel and slab door fronts rather than raised-panel traditional casework. If you are mixing it into a room with existing traditional hardware, the Unlacquered Brass or Oil Rubbed Bronze finish bridges the gap better than Polished Chrome.

All three are Omnia modern cabinet pulls in forged solid brass, and they differ mainly in how far they stand off the face: the 1969 lists 1-3/16 inch projection, the 1971 lists 1-3/16 inch, and the 1970 lists 1-1/4 inch. Each is its own series -- 1969, 1970, and 1971 Cabinet Pulls Series respectively -- so the part number is what distinguishes them at order time. The Emtek Trail sits at 1-7/8 inch projection in brass, a deeper grip than any of the three.