Emtek Bauhaus Cabinet Pull, Schaub Collection

The Bauhaus pull is stocked in 3 inch and 4 inch center-to-center. If your drawer fronts are already bored, measure hole to hole and match one of those two. The description ranges the Bauhaus design from 3 inch up to 8 inch center-to-center, but the sizes actually built out here are the 3 inch and the 4 inch, each in six finishes.

Projection is 1-3/4 inches. That is a deep grip, which matters in a galley kitchen or a tight hallway run where a passing hip catches hardware, and it also means you can get a full hand behind it with a work glove on. If you want something that sits closer to the face, the Omnia 1970 is a 1-1/4 inch projection and the Omnia 1969 and 1971 are 1-3/16 inch.

The Emtek Bauhaus pull is a residential cabinet pull. For casework in a commercial building, the Trimco 553 Series drawer pull is offered at 3 inch center-to-center and the Trimco 562 Series covers 3-1/2 inch, 4 inch, and 96mm center-to-center. The 553 at 3 inch and the 562 at 4 inch land on the same hole spacing as the 3 inch and 4 inch Bauhaus, so an existing drawer front can carry either without new holes.

The Omnia 1968/102 is a modern cabinet pull in forged solid brass at 4 inch center-to-center, so it lands on the same drilling as the 4 inch Bauhaus. The Bauhaus is a brass cabinet pull covering 3 inch to 8 inch center-to-center, so the 4 inch Bauhaus and the 1968/102 share hole spacing and you can swap one for the other without redrilling a door or drawer front. The 1968/102 is forged brass construction, which is the main build difference to weigh.

The Emtek Bauhaus pull projects 1-3/4 inch off the face. If that stands too far into a narrow aisle, the Omnia 1970 is a modern cabinet pull with a 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 both come in at 1-3/16 inch projection. All three are forged solid brass modern pulls. Half an inch less projection is the difference between a pull that catches a pocket and one that does not in a tight run.

No. The Schaub 10011 Sabre is a 4 inch center-to-center edge pull, and an edge pull mounts on the edge or face margin of a door for a flush, low-profile grip rather than standing off the face. The Bauhaus is a cabinet pull with a 1-3/4 inch projection meant to be gripped in front of the door. The 4 inch spacing matches, but the two do not do the same job on a door. The Schaub 10010 covers 3 inch and the Schaub 10012 covers 5 inch in that same edge pull line.

The spec record carries the Bauhaus pull as brass, both material and substrate, while the written specification lists zinc. On that point the two do not agree, so order to the finish and the dimensions rather than to the substrate. If solid brass is a requirement on your spec, the Deltana SBP35 square bar pull and the Omnia 1968/102 are both listed as solid brass.

Six finishes, and every one is available in both the 3 inch and 4 inch size: Oil Rubbed Bronze (US10B), Polished Nickel (US14), Satin Nickel (US15), Flat Black (US19), Polished Chrome (US26) and Satin Brass (US4). Those are standard US finish codes, so you can hold the same code across leversets, hinges and pulls when you are standardizing a whole unit or a whole floor.

Emtek carries the Bauhaus pull as residential. For a rental turn, a model unit or an owner-occupied kitchen that is what it is built for. For heavy commercial casework or an institutional millwork package, look at a heavy-duty option such as the Deltana SBP35 modern square bar pull, listed as heavy-duty solid brass.

A pull on drawers, a knob on doors, is the usual split, and the Bauhaus is a pull, mounted on two centers at 3 or 4 inches. Two fixings mean it will not spin loose the way a single-screw knob can, which is why drawers that get yanked full get pulls. If you want knobs for the door fronts alongside it, the Orca Bachelor Collection round knob and round ring knob are both 1-1/4 inch diameter, and the Orca Blackcomb square knob is 25mm.

The Deltana SBP35 is a modern square bar pull at 3-1/2 inch, built heavy-duty in solid brass. It is a square bar profile rather than the Bauhaus mid century modern shape, and at 3-1/2 inch it does not land on the Bauhaus 3 inch or 4 inch hole spacing, so plan on new holes or new fronts if you are switching an existing run.

For an appliance panel you want an appliance pull, not a cabinet pull. The Schaub 79-8 Steamworks is an 8 inch cabinet pull built as an appliance pull, which gives you the longer grip a full-height panel door needs. The Emtek Bauhaus is a cabinet pull and its center-to-center range runs 3 inch to 8 inch, so keep the Bauhaus on the drawers and boxes and use the 79-8 where a panel needs a two-hand grip.

That is the style Emtek assigns it: mid century modern, under an American Classic theme. The Bauhaus name is the giveaway, clean bar geometry rather than ornament. It reads correctly against flat slab or shaker fronts and against the flat black or satin brass trim people pair with that era.

The 4 inch center-to-center Bauhaus pull in Satin Nickel (US15) is MPN SPC86325US15. The SPC prefix is the Schaub collection line Emtek sells the Bauhaus under, and the trailing US15 is the finish code, so the other finishes in that size follow the same pattern with their own code.

The Bauhaus tops out at 4 inch center-to-center as stocked, which is short for a refrigerator or a panel-front dishwasher. For appliance fronts, the Schaub 79-8 Steamworks is an 8 inch pull carried as an appliance pull. Note that it is a different design family, so it will read as a deliberate contrast rather than a match.

No. The Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width, made of steel in satin nickel. It is a different profile and a steel body, where the Bauhaus is a brass cabinet pull in a mid century modern style. Satin nickel is a finish both can be had in, since the Bauhaus is offered in Satin Nickel US15, but matching the finish name does not make the two the same pull.