Emtek Geometric Rectangular Cabinet Pull, Schaub Collection

The Deltana SBP35 Modern Square Bar Pull is a heavy-duty solid brass square bar pull at 3-1/2 inch center to center, which lines up with the 3-1/2 inch spacing offered in the Emtek Geometric Rectangular Cabinet Pull range. Both are brass pulls with a squared-off rectangular profile, so an existing pair of 3-1/2 inch bores works for either. The Emtek Geometric is a brass pull offered from 3 inch through 12 inch center to center, so if a kitchen mixes 3-1/2 inch drawer bores with wider bores elsewhere, the Emtek range covers the full spread from one series while the SBP35 covers the 3-1/2 inch openings.

No. The Schaub 10010, 10011, and 10012 Sabre pulls are edge pulls at 3 inch, 4 inch, and 5 inch center to center respectively. An edge pull mounts at the edge of a door or drawer front and sits flush or near-flush to be grasped from the lip, which is a different mounting condition from a surface-mounted rectangular bar pull like the Emtek Geometric, even though the center to center numbers overlap with the Emtek 3, 4, and 5 inch spacings. Matching center to center alone does not make them interchangeable; confirm whether the front is prepped for a face-mounted pull or an edge application before ordering.

The Orca CK-15030 and CK-16030 Bachelor Collection items are round cabinet knobs at 1-1/4 inch diameter, the CK-16030 being the round ring version, and the Orca CK-17025 Blackcomb is a square cabinet knob at 25mm diameter. All three are cabinet knobs, which mount on a single center bore. The Emtek Geometric Rectangular Cabinet Pull is a two-bore pull sold from 3 inch through 12 inch center to center. A door prepped for a knob has one hole and a door prepped for the Emtek Geometric has two at a set spacing, so switching between them means re-boring the front.

Six finishes: Flat Black (US19), Oil Rubbed Bronze (US10B), Polished Chrome (US26), Polished Nickel (US14), Satin Brass (US4) and Satin Nickel (US15). The US codes matter if you're matching pulls to door hardware already in the house, because a US15 satin nickel pull and a US15 lever are speaking the same finish language. Oil Rubbed Bronze is a living finish and will change tone with handling over time.

Brass, both as the material and the substrate, so the finish sits on brass rather than on a die-cast pot metal core. That's the difference that shows up years in: plated zinc pulls tend to chip at the corners and pit in a kitchen or bath, brass doesn't. On a rectangular profile with defined edges, the edge is exactly where a cheaper casting gives itself away.

Emtek classifies the Geometric rectangular pull as residential hardware. For a single-family home, a condo unit, or a light-duty millwork job it's the right call. For a commercial break room, a school casework run, or anything facing institutional traffic and a specification, you want hardware rated for that duty. In a multi-family setting it works fine inside the units; think harder about lobby and amenity casework.

A rectangular pull like the Emtek Geometric gives you a full grip, which is what you want on drawers carrying weight, on doors people open with wet or gloved hands, and anywhere you want an easier grasp than a knob's pinch. Knobs suit small upper doors and cost less per opening. A common mix is pulls on all drawers and lower doors, knobs on uppers. If you decide knobs, the Orca Hardware Bachelor Collection round knob is a 1-1/4 inch diameter option, and the Blackcomb square knob is a 25mm square if you want to echo the rectangular geometry.

Several square-profile brass pulls sit in the same lane. The Deltana SBP35 is a modern square bar pull at 3-1/2 inch center to center in solid brass. Omnia's 1968 series is a forged solid brass modern pull at 4 inch center to center, and the 1969, 1970 and 1971 series are forged brass modern pulls with 1-3/16, 1-1/4 and 1-3/16 inch projections respectively, which is the number to check if you have a narrow walkway or a door that swings past a return wall. The Emtek Geometric is the one to pick when you need a single design carried across seven spacings from 3 up to 12 inches.

Projection is the published differentiator across the Omnia modern pull family: the Omnia 1969 and Omnia 1971 are forged solid brass with 1-3/16 inch projection, and the Omnia 1970 is forged solid brass with 1-1/4 inch projection. Where a drawer front sits close to an adjacent appliance panel or a door swings past a return wall, those stated projections let a contractor check the clearance before ordering. The Emtek Geometric Rectangular Cabinet Pull is a brass rectangular pull sold across 3 inch to 12 inch center to center, and is the choice when the bore spacing rather than the standoff is what governs the opening.

The Schaub 79-8 Steamworks 8 inch pull is designated an appliance pull, which is the category built for the weight and grip of a refrigerator, freezer, or range panel. The Emtek Geometric Rectangular Cabinet Pull is a cabinet knob/pull and reaches 10 inch and 12 inch center to center at the wide end of its range, so it can carry a long horizontal run on a panel front where the design calls for the same rectangular profile as the rest of the kitchen. For a designer matching one look across cabinets and appliance panels, the Emtek Geometric wide spacings keep the profile consistent; for a dedicated appliance-rated grip, the Schaub 79-8 is the item.

The Trimco 553 Series drawer pull is a 3 inch center to center drawer pull and the Trimco 562 Series is offered in 3-1/2 inch, 4 inch, and 96mm center to center, so a specifier working to a commercial casework drawing has bore spacings that line up with the Emtek Geometric Rectangular Cabinet Pull's 3 inch, 3-1/2 inch, and 4 inch spacings. The distinction that matters for a facility buyer is the intended application: the Emtek Geometric is designated residential and is a brass pull sold in six finishes including Flat Black US19, Oil Rubbed Bronze US10B, Polished Chrome US26, Polished Nickel US14, Satin Brass US4, and Satin Nickel US15, which suits multi-family unit interiors and hospitality millwork where the finish schedule drives the selection.

The Orca Hardware CK-12001 T-Pull Bar is a steel pull with a 2 inch bar width in satin nickel. The Emtek Geometric Rectangular Cabinet Pull is brass through the substrate and is offered in six finishes: Flat Black US19, Oil Rubbed Bronze US10B, Polished Chrome US26, Polished Nickel US14, Satin Brass US4, and Satin Nickel US15. Both reach satin nickel, so a run that has to read the same across a kitchen can be met either way; the difference for a property manager standardizing across units is the base material and the fact that the Emtek range carries warm finishes such as Satin Brass and Oil Rubbed Bronze alongside the nickel and chrome.

The 10 inch and 12 inch center-to-center sizes are the ones long enough for an appliance panel, and using them keeps the panel matching the surrounding cabinetry instead of standing out. Check the panel's pre-drilled hole spacing first, because appliance panels often come bored at a fixed spacing set by the appliance maker. If the spacing doesn't match, Schaub's 79-8 Steamworks 8 inch pull is a purpose-built appliance pull worth a look.

Same hardware. The Geometric rectangular pull is sold under Emtek's Schaub collection, which is why you'll see it referenced either way in specs and quotes. If a designer's schedule calls out a Schaub Geometric pull and you're ordering Emtek, you're on the right part, and the center-to-center size plus the US finish code are what pin down the exact one.