Emtek Sandcast Bronze Rustic Modern Cabinet Pull, Schaub Collection

The Deltana SBP35 Modern Square Bar Pull is a heavy-duty solid brass bar pull at 3-1/2 inch center-to-center, matching one of the center-to-center spacings the Emtek Rustic Modern pull is made in. The difference is the character of the metal: the Emtek is a sandcast bronze piece with a bronze substrate, so it carries the irregular cast texture and the Flat Black Bronze, Medium Bronze and Tumbled White Bronze finishes, while the SBP35 is a square-profile solid brass bar. If the cabinetry already has 3-1/2 inch bores and you want a crisp square bar rather than a rustic cast face, the SBP35 drops into the same hole spacing.

No - they mount differently. The Schaub 10010, 10011 and 10012 Sabre pulls are edge pulls at 3 inch, 4 inch and 5 inch center-to-center; an edge pull sits on the edge of the door or drawer front rather than the face, so it is used where a face-mounted grip would collide with a neighboring panel or where a flush look is wanted. The Emtek Rustic Modern is a face-mounted cabinet pull and ships with mounting screws for through-bored fronts. The center-to-center numbers look interchangeable, but the bore locations are not.

The Emtek Rustic Modern sandcast bronze pull is classified for residential use. For commercial drawer work the Trimco 553 Series drawer pull at 3 inch center-to-center and the Trimco 562 Series in 3-1/2 inch, 4 inch and 96mm center-to-center are drawer pull lines built for that setting, and the 562 covers two of the same spacings the Emtek is made in. Specifying institutional casework or an office fit-out, the Trimco series is the closer match; for residential millwork and high-end kitchens the Emtek sandcast bronze is the intended product.

The Deltana SBP35 is a modern square bar pull at 3-1/2 inch, heavy-duty solid brass, and it matches the same hole spacing as the 3-1/2 inch Rustic Modern. Trimco's 562 Series also covers 3-1/2 and 4 inch center to center if you want a plainer drawer pull. Any of those three drop onto the same two bores at that spacing, so it is a straight design swap without redrilling.

The 12 inch center-to-center size is the one that suits a tall appliance panel, and 8 and 10 inch cover wide drawer banks. Bear in mind this is a residential pull, and appliance panels take harder pulling than a drawer front does. If you want a purpose-built appliance pull instead, the Schaub 79-8 Steamworks 8 inch is catalogued for that function.

Three Omnia forged solid brass pulls publish projection: the 1969 and the 1971 at 1-3/16 inch, and the 1970 at 1-1/4 inch. Projection is the clearance between the door face and the back of the grip, which matters where a drawer sits next to an appliance handle or a wall return. The Emtek Rustic Modern is a sandcast bronze pull sold across 3-1/2 inch through 12 inch center-to-center, so it covers a much wider run of drawer and door widths, while the Omnia trio lets you pin the projection number on the drawing.

The Schaub 79-8 Steamworks is an 8 inch appliance pull, sized and rated for the weight of a refrigerator or range panel door. The Emtek Rustic Modern is a cabinet pull and is also made in an 8 inch center-to-center, so the two carry the same spacing and read at the same length across a panel - the Schaub 79-8 is the one built for the appliance door, the Emtek for the surrounding cabinet and drawer fronts.

For door fronts where a single-bore knob will do, the Orca Hardware Bachelor Collection CK-15030 round knob and CK-16030 round ring knob are both 1-1/4 inch diameter, and the Blackcomb CK-17025 is a 25mm square knob. All three are cabinet knobs on one screw rather than a two-bore pull, which halves the drilling on a large door count. The Emtek Rustic Modern is a two-bore pull in sandcast bronze; the usual approach is knobs on the doors and pulls on the drawers, so the Orca knobs and the Emtek pull often go into the same kitchen rather than replacing each other.

Flat Black Bronze at 5 inch center to center is SPC86669FB, and 6 inch center to center in the same finish is SPC86670FB. Give those numbers when you are matching an existing order or adding to a kitchen already installed, since the finish code FB is what keeps a later add-on from arriving in Medium Bronze.

The Orca Hardware CK-12001 is a T-pull bar with a 2 inch bar width, made of steel in a satin nickel finish. The Emtek Rustic Modern is sandcast bronze on a bronze substrate, offered in Flat Black Bronze, Medium Bronze and Tumbled White Bronze. Different metal and different look: the CK-12001 is a plated steel bar in a bright cool tone, the Emtek a cast bronze piece in warm and blackened bronze tones. Choose on which metal the rest of the room's hardware is in.