Emtek Trinity Cabinet Pull, Schaub Collection

Trinity pulls run in eight center-to-center spacings: 3", 3-1/2", 4", 5", 6", 8", 10" and 12". The 3" through 5" sizes suit drawer fronts and standard cabinet doors, while the 10" and 12" are the sizes people reach for on tall pantry doors, appliance panels and wide bank drawers. Measure the existing hole spacing, not the pull, and match it exactly if you're replacing hardware without redrilling.

Projection is 1-3/4 inches on the Trinity. That is the clearance you need between the cabinet face and anything beside it, so check it on drawers next to a wall return, an inswing door, or an appliance handle that swings past. If 1-3/4 inches is too much, the Omnia 1969 and 1971 pulls are listed at 1-3/16 inch projection and the Omnia 1970 at 1-1/4 inch.

The Trinity is a residential-specification pull. For multi-family unit turns, model kitchens and residential remodels it's the right class of hardware. If you're specifying for a commercial casework package or an institutional millwork job, look at pulls carried under commercial lines instead, such as the Trimco 553 and 562 Series drawer pulls.

The smallest Trinity is 3 inch center-to-center, so on narrow drawer fronts and slim rails that is the size to specify. Remember the overall pull is longer than its ctc spacing, so lay the actual pull against the front before you drill. If the front is too narrow for any face-mounted pull, an edge pull is the alternative: Schaub makes the Sabre edge pull in 3", 4" and 5" center-to-center, and it mounts on the edge of the door or drawer instead of the face.

The Emtek Trinity cabinet pull is a brass cabinet pull offered in center-to-center spacings from 3 inches to 12 inches, including 3-1/2 inch. For the same 3-1/2 inch spacing in a squared-off bar profile, the Deltana SBP35 Modern Square Bar Pull is a heavy-duty solid brass pull at 3-1/2 inch. Both mount on the same two-hole 3-1/2 inch drilling, so an existing bore carries over either way; the Trinity is a contemporary rounded design while the SBP35 is a square bar.

The Emtek Trinity cabinet pull covers 4 inch center-to-center within its 3 inch to 12 inch range. If you want a different look on the same 4 inch drilling, the Omnia 1968/102 is a modern forged solid brass cabinet pull with 4 inch center-to-center spacing, and the Trimco 562 Series drawer pulls are offered in 3-1/2 inch, 4 inch, and 96mm center-to-center. All three land on a 4 inch bore, so cabinet fronts already drilled for the Trinity accept any of them.

The Emtek Trinity cabinet pull has a 1-3/4 inch projection. For a tighter clearance in a galley run or against an adjacent wall, the Omnia 1970 modern cabinet pull is forged solid brass with a 1-1/4 inch projection, and the Omnia 1969 and Omnia 1971 are forged solid brass pulls at 1-3/16 inch projection. All are modern-profile brass pulls, so the change is how far the grip stands off the face.

The Emtek Trinity cabinet pull runs to 10 inch and 12 inch center-to-center, alongside 3, 3-1/2, 4, 5, 6 and 8 inch. Among the brass alternatives, the Omnia 1968/102 is set at 4 inch center-to-center and the Trimco 562 Series tops out at 4 inch and 96mm, with the Trimco 553 Series at 3 inch. For tall pantry doors and wide drawer banks where the drilling is 10 or 12 inches, the Trinity carries the run in the same brass and the same finish as the shorter sizes.

Six finishes: Flat Black (US19), Oil Rubbed Bronze (US10B), Polished Chrome (US26), Polished Nickel (US14), Satin Brass (US4) and Satin Nickel (US15). Those US codes are the standard finish designations, so if the knobs or levers already in the room are specified as US15 or US10B, the Trinity will land in the same family. Order all the pulls for a room in one go where you can, since plated brass finishes vary slightly between production runs.

For a full-height appliance panel, the 10" and 12" center-to-center Trinity sizes are the ones with the reach for it, and the 1-3/4 inch projection gives room to get a hand behind. It is a residential-grade brass pull, not a purpose-built appliance pull, so if the panel is heavy and gets hauled open all day, a dedicated appliance pull like the Schaub 79-8 Steamworks 8 inch is built for that duty.

A pull like the Trinity gives you a full-hand grip and is the usual choice for drawers, especially deep or loaded ones, and for tall doors where a knob leaves you fishing for it. Knobs suit small upper doors and lighter drawer fronts and cost less per opening. If you want knobs in the same contemporary vein, the Orca Hardware Bachelor Collection round knob and round ring knob are both 1-1/4 inch diameter, and the Blackcomb Collection square knob is 25mm. Plenty of kitchens mix the two: knobs on uppers, pulls on drawers and pantry.

The Emtek Trinity is a cabinet pull in center-to-center sizes from 3 inches to 12 inches. For an appliance door, the Schaub 79-8 Steamworks 8 inch pull is built as an appliance pull, which is the part sized and mounted for the heavier door and the longer grip an appliance front needs. Use the Trinity on cabinet doors and drawer fronts and the 79-8 where the opening is an appliance panel.

They mount differently and are not substitutes. The Emtek Trinity is a surface-mounted cabinet pull with a 1-3/4 inch projection, drilled on two centers from 3 inches to 12 inches. The Schaub Sabre pulls - the 10010 at 3 inch center-to-center, the 10011 at 4 inch, and the 10012 at 5 inch - are edge pulls, which wrap the edge of the door or drawer rather than standing off the face. If the design calls for a grip you wrap your hand around on the face of the door, the Trinity is the part; the Sabre edge pulls suit flush and pocketed applications.

The Emtek Trinity is a two-hole cabinet pull, so a knob is a different drilling - one hole instead of two. If you are running knobs on upper doors and pulls on drawers, the Orca Hardware CK-15030 Bachelor Collection round cabinet knob and the CK-16030 round ring cabinet knob are both 1-1/4 inch diameter, and the CK-17025 Blackcomb Collection square knob is 25mm diameter. Plan the bore before ordering: converting a door from the Trinity to any of these leaves a second hole to fill.

The Emtek Trinity cabinet pull is a brass residential pull in a contemporary style, with six finishes including Flat Black (US19), Oil Rubbed Bronze (US10B), Polished Chrome (US26), Polished Nickel (US14), Satin Brass (US4) and Satin Nickel (US15), and center-to-center sizes from 3 inches to 12 inches. If you are standardizing a fleet on one short size, the Trimco 553 Series drawer pull is a 3 inch center-to-center pull and the Trimco 562 Series covers 3-1/2 inch, 4 inch and 96mm. The Trinity gives you a single family that spans short drawer pulls up through 12 inch runs on tall doors, which matters when you want one look across a whole unit.

No. The Emtek Trinity cabinet pull is brass and offered in Satin Nickel (US15) among its finishes. The Orca Hardware CK-12001 is a T-Pull Bar with a 2 inch bar width, built in steel with a satin nickel finish. The finish name matches but the base material does not - if you are matching brass hardware elsewhere in the room, or the specification calls for brass, the Trinity is the one that meets it.

Contemporary. The Trinity is part of Emtek's Schaub Collection and reads as a clean modern pull, which is why it's offered in Flat Black and Polished Chrome alongside the warmer Satin Brass and Oil Rubbed Bronze. If you're matching an existing contemporary package, the Omnia 1968, 1969, 1970 and 1971 forged solid brass pulls sit in the same modern family.

No, the Trinity is straight mechanical brass hardware. It's a face-mounted cabinet pull that fastens through the drawer or door front, with no electronics, no batteries and nothing to wire.