HID 5355A-302-01 Cover, For ProxPro Reader with Keypad, Charcoal Gray

It is the cover only, a replacement housing piece for the ProxPro with keypad reader in charcoal gray. The electronics, keypad board and wiring are not part of it, so if you need a working reader you are ordering the ProxPro unit itself and using this as a replacement shell or color change.

It is made for the ProxPro with keypad, the 125 kHz proximity reader built on base part numbers 5355, 5352 and 5358. If the reader on your wall is a keypad ProxPro carrying one of those base numbers, this is the matching cover. A ProxPro without a keypad uses a different housing.

The HID 5355A-302-01 is a charcoal gray replacement cover for the ProxPro reader with keypad, so it only helps when the reader body and keypad are still serviceable. If the reader itself has to be replaced, the SDC IPRW Series is a Wiegand proximity reader with 125 kHz HID compatibility, which matches the 125 kHz credential technology the ProxPro with keypad reads. Note that the IPRW Series is a proximity reader without an integrated keypad, so openings that rely on a PIN in addition to the card would lose that capability.

The ProxPro with keypad measures 5.0 x 5.0 x 1.0 inches (12.7 cm x 12.7 cm x 2.54 cm), so the cover spans that same 5 inch square footprint and stands about an inch off the surface. Anything drilled outside that 5 inch square stays visible.

No. The cover is a housing part only. The ProxPro with keypad reads up to 8.0 inches (20.5 cm), runs on 10 to 28.5 VDC and is ordered with Wiegand, Serial (RS-232/RS-422) or Clock-and-Data output. Those are set by the reader you already have, not by the shell you put on it.

A cracked shell is a cover swap; a dead reader is not. If the electronics are gone you need a replacement 125 kHz reader, and if the opening does not require a keypad, SDC's IPRW Series Wiegand proximity reader is a 125 kHz HID-compatible option on a Wiegand output. Keep in mind it is a card-only reader, so a PIN-controlled door still wants a keypad unit.

No. The 5355A-302-01 is a cover component for the ProxPro reader with keypad and contains no electronics or read circuitry. The SDC IPRW Series is a complete Wiegand proximity reader with 125 kHz HID compatibility. They are not interchangeable: the SDC unit does not mount under an HID ProxPro cover, and the HID cover does not fit an IPRW reader. Order the 5355A-302-01 only when you are refacing an existing ProxPro with keypad.

The ProxPro with keypad that the 5355A-302-01 cover fits is a 125 kHz proximity reader with an integrated keypad, sized 5.0 in. x 5.0 in. x 1.0 in. with a read range up to 8.0 in. and 10-28.5 VDC power. For a card-only opening, the SDC IPRW Series is a Wiegand proximity reader with 125 kHz HID compatibility, so existing 125 kHz credentials already issued for the ProxPro will continue to work on it while removing the PIN entry hardware from the door.

Charcoal gray is the only finish this cover comes in, so it will match any other ProxPro keypad readers wearing the factory charcoal housing. For fleets it is a cheap way to refresh sun-faded or cracked shells on existing openings without pulling the reader off the wall and re-terminating it.

Yes, the 5355A-302-01 is a commercial access control part, supplied for electronic reader hardware rather than residential use. It is a component of an electrified opening, so treat it as part of the access control system when you spec it.