Pamex DD02-46 Door Saver II Hinge Pin Door Stop

No. The Door Saver II uses a bumperless design, so nothing presses against the door face or the trim. It stops the swing at the hinge instead, which is why it gets used where a wall or baseboard stop would mark the finish. Carbon steel construction.

Neither. The DD02-46 Door Saver II installs in seconds with no tools, and no drilling into the wall or casing. It clamps onto an existing hinge, so the door stays hung and there are no holes to patch if you move it later. That is the practical reason property managers pick a hinge pin stop over a wall stop on a turnover.

The Pamex DD02-46 Door Saver II is a hinge pin stop specified for residential application. Where the opening needs a commercial-duty hinge pin stop, the Delaney Door Saver Commercial Hinge Pin Door Stop, part 40120X, is the commercial counterpart in the same Door Saver hinge pin family, and Delaney also offers the Heavy Duty Hinge Pin Door Stop, part 402XXX. Orca Hardware carries the HPHD Series HD Hinge Pin Stop as a further heavy-duty option. All three mount on the hinge the same way the DD02-46 does, so the opening does not need new prep to change over.

The Pamex DD02-46 Door Saver II is a hinge pin door stop. Orca Hardware's hinge pin parts are catalogued with a door holder function: the HPDS Series HPDS, the HPHD Series HD stop, and the HPST Series stop all list Door Holder as their product function. For an office or unit door that has to stand open during a move-in or a service call, one of the Orca hinge pin stops answers that need while still mounting on the hinge like the Pamex.

Overall size is 4-3/4 x 3/4 inches. That is the footprint sitting on the hinge barrel, so if you have a closer arm, a hinge mounted holder, or a security hinge stud already occupying the top hinge, plan on putting the stop on a different hinge.

Four: 622 matte black, 625 polished chrome, 613 oil rubbed bronze, and 619 satin nickel. Those are standard BHMA finish codes, so you can match the stop to the hinges and lever already on the opening rather than eyeballing it. On a fleet of units, ordering to the code is how you keep the doors consistent.

The Pamex Door Saver II is a stop, not a holder. It limits how far the door swings and that is all. If you need the door to stay parked open, the Orca Hardware HPDS and HPST hinge pin units are listed with a door holder function, and the Emtek 2241 brass hinge pivot stop is the option when you want a solid brass part to match decorative trim.

For residential doors, yes, and it is the fastest one. The Door Saver II goes on with no tools and no drilling, so a maintenance tech can do a stack of units in an afternoon without patching drywall or committing to a floor stop that becomes a trip hazard. The bumperless design means no rubber tip to crush or fall out, which is the usual failure on wall stops in rental turnover.

No. The Emtek 2241 is a brass pivot stop, while the Pamex DD02-46 Door Saver II is a carbon steel hinge pin stop with a bumperless design and an overall size of 4-3/4 inches by 3/4 inches. The two look alike in a photo because both sit at the hinge, but the Emtek is a brass part in a different series, so a buyer matching an existing steel Door Saver II across a set of doors should stay on the Pamex or on another hinge pin stop rather than order the 2241.

The Pamex DD02-46 Door Saver II uses a bumperless design that eliminates damage to doors and trim, and it installs in seconds with no tools. Among the other hinge pin stops, the Delaney Door Saver Commercial 40120X and Heavy Duty 402XXX, and the Orca HPDS, HPHD, and HPST series stops, are all hinge-mounted parts in the same category, but the bumperless Door Saver II construction is the specific point a buyer replacing torn-out bumpers is after. It is offered in matte black 622, polished chrome 625, oil rubbed bronze 613, and satin nickel 619 to match existing hinge finishes.

Carbon steel, listed as a steel substrate. Steel takes the repeated impact of a swinging door better than a cast decorative part, but it is a plated finish over steel, so for a coastal or high humidity opening the Emtek 2241 brass unit is the material to look at instead.