Rockwood 94PX94L Flush Pull Set

The 94P x 94L set ships with 1/4-20 x 1-1/2 inch thru bolts sized for a standard 1-3/4 inch door. On anything thicker or thinner, the bolt length has to change, so the door thickness needs to be specified when ordering. Rockwood's own note on the set says to advise if the door thickness is other than 1-3/4 inches.

It pairs the 94P pull with the 94L pull, mounted back to back through the door and fastened with 1/4-20 x 1-1/2 inch thru bolts. That gives you a flush pull on both faces of the same door, which is what a sliding, pocket or barn door needs so the leaf can be moved from either side with nothing projecting past the face.

It is a commercial-duty pull built to ANSI A156.6, type J403, the standard covering architectural door trim. Rockwood lists the set at .125 inch material thickness, and the US32D version is stainless steel, which is the usual choice for schools, healthcare, offices and other high-traffic openings.

For commercial openings, Trimco's 1060/1061 flush cup pulls and the larger 1111 Series cover the same job in a mortised cup format, and the Trimco 1059 is a drive-in version if you would rather not through-bolt. Where a recessed pull has to be dropped for a full grip, the Trimco 1066/1067/1068 drop-ring flush pulls add a swing-down ring. On residential pocket and bi-fold doors, the Sure-Loc DP5 finger pull at 2-1/8 inches and the Baldwin Estate 8601 pocket door pull are the lighter-duty options.

For a psychiatric or behavioral health opening, look at the ABH 1911 Series flush door pull instead. It is built with a ligature-resistant design, which is the specific requirement in those rooms. The Rockwood 94P x 94L is a standard commercial flush pull set in stainless steel meeting ANSI A156.6, J403 - appropriate for offices, schools, hotels and general institutional doors, but it is not offered as a ligature-resistant product.

The Trimco 1060/1061 flush cup pulls are the nearest commercial-grade counterpart. Like the Rockwood 94P x 94L set, they are flush cup pulls intended for doors where nothing can project past the face of the leaf. The Rockwood set is through-bolted with 1/4-20 x 1-1/2 inch thru bolts sized for a standard 1-3/4 inch door, so if the opening was detailed for a thru-bolted pair of pulls the 94P x 94L is the direct match; the Trimco 1060/1061 is the alternative when you are matching an existing Trimco set elsewhere in the building.

Consider the Trimco 1059 drive-in flush cup pulls. They are a drive-in style cup pull rather than a thru-bolted set, so they do not depend on a matched pair of pulls on both faces. The Rockwood 94P x 94L ships with 1/4-20 x 1-1/2 inch thru bolts sized for a 1-3/4 inch door, so on any other door thickness the bolt length has to be specified at the time of order.

US32D, satin stainless steel. That is the most common commercial finish in North America, so it lines up with satin stainless push plates, pulls and lever trim already on most institutional openings. The set itself is stainless steel substrate in this finish.

Yes. A TORX option substitutes security Torx screws for the standard fasteners, which is worth specifying in detention, behavioral health, school restroom and other openings where a standard driver in the wrong hands is a problem.

It is a flush pull, so the door is mortised for the cup and the two halves are pulled together with thru bolts. Because it mounts through the leaf, the door has to be prepped before the set goes on, not after the door is hung tight in a pocket.

Yes. The Sure-Loc finger pull is a 2-1/8 inch pull made for pocket and bi-fold doors, and the Orca Hardware round flush pull is also 2-1/8 inch in diameter - both are small single-cup pulls for light residential use. The Rockwood 94P x 94L is a commercial product in stainless steel, through-bolted with 1/4-20 x 1-1/2 inch bolts, which is more hardware than a closet or interior pocket door usually needs.

On a heavy or tight-running sliding leaf, the Trimco 1066/1067/1068 drop-ring flush pulls give you a ring that folds out of the cup so a full hand grip is available, and the Trimco 1111 Series large flush cup pulls offer a bigger cup opening. The Rockwood 94P x 94L is a plain recessed cup pull set - flush to the door face with no moving ring - which suits pocket and bypass doors that glide easily.

The 94P x 94L is a pull set only - two recessed cups that let you grip and move the leaf, with no latching or privacy mechanism. If the pocket door needs a locking or dummy trim assembly, the Baldwin Estate 8601 pocket door pull is offered for passage and dummy applications. Pair the Rockwood set with a separate pocket door lock if the opening needs to secure.

Rockwood builds the 94 series flush pulls from .125 inch material, offered in aluminum, brass, bronze or stainless steel. The US32D set is stainless steel, which is the one to take on wet, coastal or heavy-cleaning environments where brass and bronze will patina.

The 94P x 94L is a thru-bolted flush pull set with 1/4-20 x 1-1/2 inch bolts for a 1-3/4 inch door, which is heavier than most bi-fold panels are built for. For bi-folds, the Sure-Loc bi-fold door pull and the Sure-Loc 2-1/8 inch finger pull are made for that application, the finger pull also covering pocket doors. Reserve the Rockwood set for full-thickness commercial sliding and pocket leaves.