You may also like
Ruud AS36352-2H 3" Draft Hood Vent Fitting for Gas Water Heaters
Model: RUU-AS36352-2H
Ruud AS36352-2H 3" Draft Hood Vent Fitting for Gas Water HeatersThe Ruud AS36352-2H is a 3" draft hood designed as a replacement venting component for gas-fired water heating equipment. A draft hood...
Ruud
$12.21
Ruud RTG20151A-1 90° Vent Elbow Fitting
The Ruud RTG20151A-1 is a 90° elbow fitting engineered as a factory-matched component for Ruud water heating and venting systems. Rough-in and service plumbers use this elbow to redirect vent or supply piping runs by a full 90° turn where a straight run isn't possible, keeping the installation compact and code-appropriate for tight mechanical closets, attic runs, and closet installations behind the unit. As a Ruud-branded component, it is intended to be paired with other Ruud system parts to maintain a consistent, manufacturer-matched piping or venting assembly rather than mixed with generic aftermarket fittings.
Key Features
- 90° Elbow Configuration: Provides a full quarter-turn direction change in the piping or venting run, allowing installers to route around framing, joists, or adjacent equipment without adding unnecessary straight-run length.
- Ruud Factory-Matched Component: Manufactured under the Ruud brand for use with compatible Ruud water heater and venting assemblies, helping installers maintain a single-source parts trail for service and warranty documentation.
- Rough-In / Behind-the-Wall Application: Designed for use in the concealed piping or venting section of the installation, not as a visible or decorative fitting, so it should be installed and supported per the unit's installation instructions.
- Direct-Fit Replacement Part: Identified by Ruud part number RTG20151A-1, making it straightforward for contractors and service techs to cross-reference against the original equipment parts list when replacing a damaged or failed elbow.
Technical Specifications
- Brand: Ruud
- Part Number: RTG20151A-1
- Configuration: 90° Elbow
Typical Applications
- Water Heater Vent or Piping Direction Changes
- Residential and Commercial Mechanical Room Rough-In
- Service and Replacement of Damaged Elbow Fittings
- New Construction Installations Using Ruud Equipment
- Tight-Clearance Routing Around Framing or Adjacent Equipment
Why Ruud?
Ruud is a long-established manufacturer of water heating equipment, and factory-branded components like the RTG20151A-1 elbow are built to fit and function as part of a complete Ruud system. Choosing the manufacturer-matched fitting over a generic substitute helps installers keep the piping or venting assembly consistent with the original equipment design, which simplifies future service calls and parts lookups.
Manufacturer Resources
Product Specs
- list_batch:
- RUU-20260924
- Product Type:
- Elbow
- Angle:
- 90°
- Department:
- Plumbing
- Product Subgroup:
- Fittings and Valves
Ruud RTG20151A-1 – Frequently Asked Questions
1) What does the Ruud RTG20151A-1 elbow do in a water heater install?
The RTG20151A-1 is a 90 degree elbow used to turn a vent or supply piping run a full quarter turn where a straight shot isn't possible. Rough-in and service plumbers use it to route around framing, joists, or adjacent equipment in tight mechanical closets and attic runs without adding straight-run length.
2) Is the RTG20151A-1 a genuine Ruud part or an aftermarket fitting?
It's a Ruud-branded, factory-matched component, identified by Ruud part number RTG20151A-1. That part number is what you cross-reference against the original equipment parts list when you're replacing a damaged or failed elbow, and it keeps a single-source parts trail for service documentation.
3) Can I mix this Ruud elbow with generic aftermarket vent fittings?
It's intended to be paired with other Ruud system parts to keep the venting or piping assembly manufacturer-matched, not mixed with generic aftermarket fittings. On a Ruud unit, staying with the factory component keeps the assembly consistent with the original equipment design and simplifies later parts lookups.
4) Will one 90 degree elbow get me around a joist, or do I need two?
Each RTG20151A-1 gives a single full quarter-turn direction change. An offset around a joist or around adjacent equipment and back onto the original axis takes two elbows; a single turn into a different run takes one. Count the turns on your routing before you order quantity.
5) Is this elbow meant to be exposed or hidden behind the wall?
Concealed work. The RTG20151A-1 is for the hidden piping or venting section of the installation, not a visible or decorative fitting, and it should be installed and supported per the unit's installation instructions.
6) Is the RTG20151A-1 suitable for commercial mechanical room work or residential only?
Both. Typical applications include residential and commercial mechanical room rough-in, new construction on Ruud equipment, and service replacement of a damaged elbow on an existing unit.
How fast can I get the Ruud RTG20151A-1 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Ruud RTG20151A-1 come with a warranty?
Absolutely. The Ruud RTG20151A-1 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Ruud RTG20151A-1?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Ruud RTG20151A-1 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.