You may also like
SATCO Lighting S11233 3.5W, JCD LED, Frost, 4000K, G9 Base, 120V
3.5 Watt - JCD LED - Frost - 4000K - G9 Base - 120 Volt
Manufacturer Resources
Spec Sheet
Product Specs
- Amps:
- 0.029A
- Avg Rated Hours:
- 25000
- Burning Position:
- Universal
- CCT Selectable:
- No
- DLC Approved:
- No
- Dimmable:
- No
- Enclosure Rating:
- Enclosed Rated Lamp
- FCC Compliant:
- Yes
- Housing Color:
- Frost
- Lamp Filament:
- LED
- Lamp Shape:
- T4
- Lens Finish:
- Frost
- Lens Material:
- Plastic
- Lumens:
- 300L
- Operating Frequency:
- 60Hz
- Product Type:
- LED
- Three-Way:
- No
- Warranty:
- 3 Year Limited - 10 hr per day
- Product Group:
- Indoor Lighting
- Product Subgroup:
- Light Bulbs
- Bulb Base:
- G9 Double Loop
- Base Material:
- Ceramic
- Incandescent Equivalent:
- 35W
- Location Rating:
- Damp
- CRI:
- 80
- Subcategory:
- LED
- Location Indoor/ Outdoor:
- Indoor
- Title 24 Compliant:
- Yes
- Bulb Type:
- LED
- Product Voltage:
- 120V
- Beam Spread Angle:
- 300
- Light Temperature:
- 4000K
- Product Category:
- Light Bulbs
- Product Wattage:
- 3.5W
- Product Weight:
- 0.03 lb
- Product Material:
- Ceramic / Polycarbonate (PC)
Satco Lighting S11233 – Frequently Asked Questions
1) Can the Satco S11233 G9 LED be used on a dimmer switch?
No. The S11233 is not dimmable, so it needs to run on a plain on/off circuit. Put it on a dimmer and you can expect flicker, buzz, or no start at all. If the fixture is on a wall dimmer that you cannot change out, choose a G9 LED that is specifically listed as dimmable instead.
2) Will this G9 LED replace a 35W halogen capsule in my sconce?
That is exactly the swap it is built for. The S11233 draws 3.5 watts and is rated as a 35W incandescent equivalent, putting out 300 lumens at 4000K. The G9 double loop base drops into the same socket as a halogen G9 capsule, and the bulb runs on line voltage, 120V at 60Hz, so no driver or transformer is involved. Note the color: 4000K is a neutral white, noticeably cooler than the warm yellow light of the halogen you are pulling out.
3) Can I use the Satco S11233 in a fully enclosed fixture?
Yes, it is an enclosed rated lamp, so a sealed sconce, pendant globe, or closed ceiling fixture is fine. It also has a universal burning position, meaning base up, base down, or horizontal all work without affecting rated life.
4) Is this G9 bulb OK for a bathroom vanity or a covered porch?
Damp location rated and listed for indoor use, so a bathroom vanity or a similarly humid indoor spot is within rating. A covered exterior porch is not covered by a damp indoor rating in the way a wet-rated lamp would be, so for anything exposed to weather or direct water, specify a wet-location lamp and fixture instead.
5) Does the 4000K color on this Satco G9 LED match the rest of my fixtures?
Only if your other lamps are also 4000K. This one is fixed at 4000K neutral white with a CRI of 80, and it is not CCT selectable, so there is no field switch to change it to 2700K or 3000K. For a building where the sconces and cans are all warm white, a 3000K G9 will blend; mixing 4000K into a warm-white run reads obviously bluer on the wall.
6) How is the light spread on a frosted JCD G9 LED versus a clear one?
The frosted lens diffuses the LED chips so you get a 300 degree beam spread, close to all-around light, and you don't see hot spots or individual diodes through a shade. That makes it a good fit for open-shade sconces and chandeliers where the bulb is visible. A clear capsule instead gives a sparkle effect but shows the diodes.
7) How long does the Satco S11233 last and what does it draw on the circuit?
Rated 25,000 average hours at 3.5 watts, drawing 0.029 amps on a 120 volt, 60Hz circuit. That current is small enough that a long run of G9 sconces on one 15 or 20 amp branch is a non-issue from a load standpoint, which is the main reason property managers move halogen G9 fixtures over to LED in the first place.
8) Does this bulb count for California Title 24?
Yes, the S11233 is listed as Title 24 compliant, and it is FCC compliant. It is not DLC listed, so if a utility or commercial rebate program you are filing under requires a DLC-qualified product, this lamp will not satisfy that particular requirement.
9) What shape and base does Satco S11233 use, and how do I order the right one?
It is a T4 shape JCD-style capsule with a G9 double loop base and a ceramic base body with a plastic frosted lens. Order by Satco part number S11233 for the 3.5W 4000K frost version. G9 pins are on tight spacing, so confirm your socket is G9 and not the similar-looking G4 or GY6.35 bi-pin before ordering a case.
10) Can this G9 LED be used in a three-way fixture?
No. It is not a three-way lamp, so in a three-way socket it will operate as a single fixed output rather than stepping through levels. Same goes for dimming: the lamp is non-dimmable, so treat it as a full-on or full-off bulb.
How fast can I get the Satco Lighting S11233 delivered?
Most orders ship the same day from our distribution partners, with quick delivery throughout the
continental
U.S.
Need it urgently? Contact Us for expedited shipping options.
Can I return it if it doesn’t work for me?
Yes—ZenSupply offers a hassle-free return policy. If the product isn’t the right fit,
reach out to our support team for a return authorization or setup a return by following our return instructions.
Does the Satco Lighting S11233 come with a warranty?
Absolutely. The Satco Lighting S11233 is backed by a manufacturer’s warranty.
For full warranty terms, check the product documentation or Contact Us.
How do I get technical support or installation help for the Satco Lighting S11233?
You can call, text, or email our expert support team for fast answers. We’re here to help with
product
selection,
installation tips, and troubleshooting. Contact Us
Why buy the Satco Lighting S11233 from ZenSupply?
ZenSupply makes it easy to get the commercial door hardware you need—fast shipping, expert support,
and
rewards on
every order.
Our team is always ready to help you choose the right product for your project.