Schaub 202 6" Center to Center Northport Flat Cabinet Pull

The Schaub 202 Northport flat pull is built on a zinc base with a 6 inch center-to-center and 1-1/2 inch projection. If the specification calls for solid brass, the Omnia 1968/102 is a forged solid brass cabinet pull at 4 inch center-to-center, and the Deltana SBP35 is a heavy-duty solid brass square bar pull at 3-1/2 inch. Both are shorter across the mounting holes than the 202, so a swap on an existing drilled front would mean new holes unless the fronts are undrilled.

The Schaub 202 Northport projects 1-1/2 inch off the face of the door. For a narrower walkway, the Omnia 1970 projects 1-1/4 inch and the Omnia 1969 and Omnia 1971 each project 1-3/16 inch, all in forged solid brass. Those three give you roughly a quarter inch to five sixteenths of an inch back toward the door face per pull.

Only if you are redrilling. The Schaub 202 Northport is a 6 inch center-to-center pull with a 7 inch overall length. The Trimco 553 series is 3 inch center-to-center and the Trimco 562 series comes in 3-1/2 inch, 4 inch, and 96mm center-to-center. None of those hole spacings line up with a 6 inch bore pattern, so they are alternates for a new front rather than a drop-in replacement for the 202.

Projection is 1-1/2 inches on the Northport 202, with a 1-1/2 inch base dimension. That is a deep-standing pull, so check clearance where a drawer or door sits next to a perpendicular wall, an appliance panel, or an inside corner run. On a tight galley it can be the difference between a knuckle clearing and not.

Eight finishes across the Northport 202: Satin Nickel, Brushed Nickel, Polished Nickel, Polished Chrome, Ancient Bronze, Brushed Bronze, Matte Black, and Signature Satin Brass. That spread covers most standard multi-family and spec-home palettes, so a property manager standardizing across units can hold one collection and one finish code.

Base material on the Northport 202 is zinc, not solid brass. For a finish-critical or high-touch commercial application where solid brass is specified, the Omnia 1968/102 and Omnia 1970 are forged solid brass cabinet pulls, and the Deltana SBP35 is a solid brass bar pull.

The Northport 202 has a 1-1/2 inch base dimension at each post, so it wants a flat bearing surface at least that wide under each foot. On a shaker drawer front the flat field is usually continuous, so it mounts fine. On a five-piece door where the pull would cross from rail onto a recessed panel, the feet will not sit flush.

The Schaub 202 Northport is a 6 inch center-to-center pull, which suits wide drawers and full-height doors. For the smaller fronts in the same package, single-hole knobs avoid a second bore: the Orca Hardware Bachelor Collection round knob and round ring knob are both 1-1/4 inch diameter, and the Blackcomb Collection square knob is 25mm. Those are knobs rather than pulls, so they mount on one screw instead of the 202's two-hole pattern.

The 202 is part of Schaub's Northport collection in a transitional style, a common approach being pulls on drawers and knobs on doors. Schaub styling also carries through Emtek's Schaub Collection lines, including the Emtek 8405 Select cabinet pulls and knobs, if you want a coordinating knob from the same design family.

The Schaub 202 Northport is a flat transitional pull in zinc. For a heavier industrial profile, the Orca Hardware CK-12001 is a steel T-pull bar with a 2 inch bar width in satin nickel. The 202 also offers satin nickel among its finishes, so the two can sit in the same finish family if you are mixing profiles across a kitchen and a utility run.

No. The SDC SP50 is a 50mm spindle used in door control hardware, not a cabinet pull. The Schaub 202 Northport is the cabinet pull, mounting through the drawer front on 6 inch center-to-center holes with 8/32 x 1 inch screws.