Schaub 207 6" Center to Center Northport Cabinet Pull

The Schaub 207 Northport cabinet pull is a zinc base material pull with a 6 inch center to center spacing and a 1-1/2 inch projection. If solid brass construction is the requirement, the Omnia 1968/102 modern cabinet pull is forged solid brass with 4 inch center to center spacing, and the Omnia 1970 modern cabinet pull is forged solid brass with a 1-1/4 inch projection. The Omnia parts sit at a different hole spacing and projection than the 207, so a swap into existing 6 inch drilling is not direct - the Omnia 1968/102 at 4 inch center to center needs new bores in a door or drawer front already drilled for the 207.

The Schaub 207 Northport pull is fixed at 6 inch center to center with a 7 inch overall length, which is more than a narrow drawer front will take. For tighter spacing, the Trimco 553 series drawer pull is a 3 inch center to center part, the Trimco 562 series drawer pull offers 3-1/2 inch, 4 inch, and 96mm center to center options, and the Deltana SBP35 modern square bar pull is a 3-1/2 inch heavy-duty solid brass pull. The Trimco 562 covering three spacings in one series is the practical choice when drawer widths vary across a run of cabinets and you want one part number family.

The Schaub 207 Northport pull projects 1-1/2 inch off the front. Where clearance to an adjacent wall, appliance, or door swing is tight, the Omnia 1970 modern cabinet pull is a forged solid brass pull with a 1-1/4 inch projection, and both the Omnia 1969 and Omnia 1971 modern cabinet pulls are forged solid brass with a 1-3/16 inch projection. Those three sit closer to the face than the 207, which matters most on an inside corner cabinet or a drawer next to a range handle.

Projection is 1-1/2 inches, measured from the face of the door to the back of the grip. That's a generous hand clearance, good for gloved hands or a kitchen where people grab hard, but worth checking in a tight galley or where a drawer front sits next to a perpendicular wall or an appliance handle. The mounting posts sit on a 1 inch base.

The Northport 207 is zinc base material with a plated finish. Zinc holds a decorative finish well and is the normal material for a pull at this size, but for heavy-turnover MRO work where hardware gets hit by carts or cleaned aggressively, a solid brass pull is the tougher body. Deltana's SBP35 square bar pull and Omnia's 1968, 1969, 1970 and 1971 series pulls are forged or solid brass options in the same category.

A 6 inch center pull like the Northport 207 is the right call on wide drawers and full-height doors, where a single grip point makes the front feel unbalanced and a longer bar spreads the pull. Knobs suit small upper doors and narrow drawers. If you want knobs to match the same casework, Orca Hardware's Bachelor Collection round knobs come at 1-1/4 inch diameter and the Blackcomb square knob at 25mm.

The 207 is only a 6 inch center pull, so shorter runs need a different part. Trimco's 553 Series drawer pulls come at 3 inch center-to-center, and the 562 Series offers 3-1/2 inch, 4 inch and 96mm centers. Deltana's SBP35 is a 3-1/2 inch square bar pull. None of those are Northport styling, so if the look has to carry through, keep the 207 on the doors and pick one contrasting family for the small drawers rather than a near-miss.

No - the Schaub 207 Northport is a two-hole cabinet pull drilled at 6 inch center to center and fastened with 8/32 x 1 inch screws. A knob mounts on a single hole. The Orca Hardware Bachelor Collection round cabinet pull knob is a 1-1/4 inch diameter knob, the Bachelor Collection round ring cabinet pull knob is also 1-1/4 inch diameter, and the Blackcomb Collection square cabinet pull knob is 25mm diameter. Any of these leaves one of the two existing 207 bores exposed, so knobs suit new fronts or fronts being replaced, not a retrofit into 6 inch drilling.

The Schaub 207 Northport pull has a zinc base and a 1-1/2 inch projection. Where a heavier grip is wanted, the Deltana SBP35 modern square bar pull is a heavy-duty solid brass bar pull at 3-1/2 inch, and the Orca Hardware CK-12001 T-pull bar is a steel pull with a 2 inch bar width in satin nickel. Both are shorter or differently shaped than the 207's 6 inch center to center, so a fleet swap across an existing cabinet run means re-drilling rather than dropping into the same holes.

Transitional, from Schaub's Northport collection. It splits the difference: not the flat square bar of a strictly modern program, not an ornate traditional pull either, which makes it workable in a kitchen or millwork package that has to sit alongside both. For a straight modern square bar look instead, Deltana's SBP Series and the Omnia 1968 through 1971 pulls are the modern-styled options.

The Schaub 207 Northport is a transitional style cabinet pull at 6 inch center to center. On the modern side, the Omnia 1968/102, 1969, 1970, and 1971 are all modern cabinet pulls in forged solid brass, and the Deltana SBP35 is a modern square bar pull. The Emtek Art Deco cabinet pull is a further departure again with its own period styling. Mixing the 207 with any of these in the same room reads as two different design languages, so pick one family for the run.