Schaub 574 3" Center to Center Atherton Hammered Knurled Edge Cup Pull

Yes, if your drawers are bored on 3 inch centers. The Atherton 574 cup pull is a 3 inch center-to-center pull, which is one of the two most common legacy bore spacings on American cabinetry, so it drops onto existing 3 inch holes without redrilling. Overall length is 4-1/2 inches, so it covers a bit of face on either side of the holes.

No. A cup pull is directional, with an open cup at the bottom edge, and it is made to be gripped from underneath on a horizontal drawer face. For the doors in the same run use a knob or a bar pull. Orca Hardware's Bachelor Collection round knob at 1-1/4 inch diameter is one door-side option we carry.

The Schaub 574 Atherton cup pull is fixed at 3 inch center-to-center with an 8/32 screw size, so it will not reach wider existing holes. For 3-1/2 inch centers, the Deltana SBP35 square bar pull is a 3-1/2 inch solid brass pull; the Trimco 562 Series covers 3-1/2 inch, 4 inch, and 96mm center options in one series, and the Omnia 1968/102 is a forged solid brass pull on 4 inch centers. Measure hole to hole on the existing bore and match it before ordering.

The Trimco 553 Series drawer pulls are also built on 3 inch center-to-center spacing, so they land on the same two holes as the Schaub 574 Atherton cup pull. The difference is character: the Schaub 574 is a traditional-style hammered, knurled-edge cup pull in solid brass with a 1-1/2 inch projection, while the Trimco 553 is a straight drawer pull series. If the cabinet is already bored at 3 inch centers and you want a flat-faced pull instead of a cup, the 553 is the drop-in geometry.

Projection is 1-1/2 inches off the face. That is deep enough to get a full set of fingers into the cup, which is what a cup pull is for, but it is also something to check on a galley or against an adjacent perpendicular run where a drawer front sits close to a wall or appliance.

Solid brass, not plated zinc or stamped steel. Solid brass carries the threads for the 8/32 screws in the casting itself and takes the hammered, knurled-edge texture without it wearing flat, which matters on a drawer opened several times a day.

Four: Oil Rubbed Bronze, Polished Chrome, Polished Nickel, and Satin Brass. If you are running knobs on the doors and these cups on the drawers, stay inside the Atherton collection in the same finish so the hammered texture and the plating match across both.

A cup pull like the Schaub 574 Atherton is a traditional-style, one-hand hooked grip and reads period or transitional; it only mounts on a drawer, since the cup has a top and a bottom. A bar pull works on both doors and drawers and suits contemporary work. If the look you want is modern, the Deltana SBP35 square bar pull or the Omnia 1968/102 forged brass pull are the alternatives to look at instead.

The Schaub 574 Atherton is a traditional-style hammered, knurled-edge cup pull in solid brass. For a contemporary face on the same job, Omnia's forged solid brass cabinet pulls run modern: the 1969 and 1971 both project 1-3/16 inch and the 1970 projects 1-1/4 inch, all shallower than the 1-1/2 inch projection of the Schaub 574. Emtek's Bar cabinet pull in the Schaub Collection is another modern profile. Confirm the center-to-center of whichever model you pick against your existing bore.

The Schaub 574 Atherton cup pull mounts on two holes at 3 inch center-to-center with 8/32 screws, so it needs a drilled pair. For single-bore doors, Orca Hardware's Bachelor Collection round cabinet knob and round ring knob are both 1-1/4 inch diameter, and the Blackcomb Collection square knob is 25mm. Those are knobs, so the look will differ from the hammered brass cup, but they suit a one-hole prep.

It belongs to Schaub's Atherton collection, which lets you specify the same hammered, knurled-edge look across the other pieces in that line and hold one finish across a whole floor of units. Emtek also lists Schaub Collection cabinet hardware, including the Emtek 8405 Select and the Alexander and Art Deco pulls, if you need additional profiles under the same design program.

They serve different specs. The Orca Hardware CK-12001 is a steel T-pull bar with a 2 inch bar width in satin nickel, aimed at a utilitarian bar-pull look. The Schaub 574 Atherton is solid brass, traditional in style, and offered in Oil Rubbed Bronze, Polished Chrome, Polished Nickel, and Satin Brass. If the finish schedule calls for a brass-base decorative cup pull, the steel T-pull will not match either the material or the profile.